12"-24" Electric Sending Unit -Tank Depth- Moeller

12"-24" Electric Sending Unit -Tank Depth- Moeller
Your Price: $27.84
Save: $2.15
(7% Off $29.99)
Part # 035729-10 ValueShip™ Eligible
SHIPS TODAY!* if ordered in 11 hrs 26 mins.
Moeller

Product Families

Universal Electric Sending Unit
    The Moeller Electric Sending Unit is designed to gather information the level of fuel in the tank. This swing arm electric sending unit conveniently …

    • Swingarm Electric Sending Units gather fuel level information the same way as the mechanical sending units. It does, however, connect to a dash mounted gauge without a conversion capsule.
    • Do it yourself friendly- measure the tank depth and make the swingarm the correct length.
    • Internal components will not rust or corrode.
    • Float rotates easily in 90 degree increments for tanks wall & baffle clearance.

    Based On 8 Reviews | Write Review
    Fuel tank sending unit
    by James from Gainesville, Georgia on September 04, 2013
    I had problems finding the right unit for my boat, but found it @ iboats.It was easy to identify the correct unit by the pictures and received the product within 4 days after placing order.
    Was this review helpful?
    Worked as planned
    by Dan from Lake Havasu City, Arizona on June 13, 2013
    I replaced an old Medallion unit that is no longer in production. In end all worked fine. Dan A.
    (1 of 1 people found this review helpful)
    Was this review helpful?
    The design needs work
    by Thomas from Dadeville, Alabama on April 23, 2013
    I was finally able to get this thing to fit, but it suffers from either a poor design or poor installation instructions. To begin with, it doesn't look like this picture. The float-on-a-wire attaches to a vertical piece that hangs down into the tank. The installer has to cut the vertical piece to the correct length for the tank. The problem is that the float/wire piece will not hang straight down for installation. It always sticks out about 30 degrees from vertical. That makes the size of the unit too big to fit through the mounting hole in the tank. As the size of the mounting hole is determined by the bolt circle on the gauge, there is no reason they should have not seen this problem coming. I had to put an S-bend in the wire while hoping I didn't damage the unit to get it to fit.
    (1 of 1 people found this review helpful)
    Was this review helpful?
    Sending unit
    by Timothy from Bellevue, Kentucky on October 18, 2012
    I installed the unit and it is working fine. Thanks Iboat.
    (0 of 1 people found this review helpful)
    Was this review helpful?
    electric sending unit
    by Lenord from 100 Mile House, British Columbia on September 20, 2012
    Awesome works great
    (0 of 1 people found this review helpful)
    Was this review helpful?
    Universal Sending Unit
    by Michael from Jacksonville, Florida on September 11, 2012
    The clips holding the float leave a lot to be desired. However, there are extras provided if you need them. The 12 - 24" is not made like the picture shows. You have a bracket extending down from the top of sending unit. Then you decide, using the instructions, where to mount the floating swing arm and float to that bracket. The black mount is not mounted to a plate as shown. You have to mount it to a much longer bracket. You will have to cut this bracket below where you mount the floating arm. Then you will have to cut float arm to proper length. For the floating swing arm, the instructions give you the suggested length for the depth of your tank. Wire connection to floating arm must be mounted on the bottom to work properly. Depending on where you mount the floating arm on the bracket and where you cut the floating swing arm, this will decide where and when the sending unit will read full and empty, so measure correctly and mount bracket higher or leave swing arm longer if you want to leave some type of reserve when your gauge reads empty. The parts are made of light weight aluminum that bend very easily. If you bend the swinging float arm while installing, your reading will be incorrect. If you have a deep tank and your clearance above the mounting hole in the tank can not be installed by going straight down, it would be very easy to bend. My tank was 22 inches deep and only 5-6" below the gunnel, so I had to install at an ankle and try not to bend the arm. It would be nice if iboats offered a one piece sending unit, like the one shown, in a longer depth than 12".
    (1 of 1 people found this review helpful)
    Was this review helpful?
    Perfect
    by Jason from Pompton Plains, New Jersey on August 07, 2012
    Im usually a little leary of universal fit products. This was easy to adapt to the size I needed. Instructions are easy to follow and clear. I would definitely recommend.
    Was this review helpful?
    Easy installation
    by Mark from Athens, Georgia on April 10, 2012
    20 gal tank-15 min to install. works like a charm.
    (2 of 2 people found this review helpful)
    Was this review helpful?
    Q:
    Everything seems good except for the switch. can i buy the switch only/?
    A:
    Unfortunately, we do not carry the switch separately. If you need help finding it, you can post a question on our Forum. Thousands of boaters visit there every day and can assist you in finding just the switch. You can access the Forum page at http://forums.iboats.com/
    Ask a question for
    Question & Answer Guidelines
    This product ships in 1 business day.

    Add to Cart and enter your Postal Code to determine the shipping charges and estimated delivery date.
    * Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
    Standard Shipping Policies