CMC Electric Hydraulic Power Tilt And Trim

Electric Hydraulic Power Tilt And Trim PT-130 with Gauge - CMC
Your Price: $785.08
Save: $114.91
(12% Off $899.99)
Part # 13001
Electric Hydraulic Power Tilt And Trim PT-35 - CMC
Your Price: $561.61
Save: $78.38
(12% Off $639.99)
Part # 52100
Electric Hydraulic Power Tilt And Trim Transom Adapter, for Clamp Motor - CMC
Your Price: $70.97
Save: $12.52
(14% Off $83.49)
Part # 13022 ValueShip™ Eligible
CMC

Enhance the performance of your outboard with the CMC Electric Hydraulic Power Tilt and Trim. It features 6061 T6 extruded aluminum construction and comes with stainless steel fasteners to assure solid and durable use round the year. This tilt and trim allows you to easily tuck-in and alter the angle of outboard motor to improve its performance in any load or water condition. Plus, you can quickly raise the motor to protect it from damage with just a push of a switch. This trim and tilt has long set back that improves boat stability. Its waterproof marine electric hydraulic actuator is rated at 7853 lbs.

  • Made of 100% non-ferrous material – suitable for use in freshwater and salt water
  • 7853 lbs rated electric hydraulic actuator
  • Easy to tuck in, alter or raise the motor

This electric hydraulic power tilt and trim comes with or without gauge. It is available in two sizes for use with different outboards.

Features of CMC Electric Hydraulic Power Tilt and Trim:

  • Enhances boat’s stability
  • Increases top end speed
  • Offers better prop clearance
  • Reduces fuel consumption
  • 6061 T6 extruded aluminum construction with stainless steel fasteners
  • 100% non-ferrous material
  • Allows easily tuck-in or alter angle of motor
  • Allows raising motor with a simple push of switch
  • Electric hydraulic actuator rated at 7853 lbs. of thrust
  • Totally sealed submersible hydraulic system runs without water damage
  • Standard B.I.A. bolt hole pattern (13001 & 13002)
  • Convenient adapter kit available for clamp-on motors (13001 & 13002)
  • Includes four stainless steel motor mounting bolts
  • PT-35 accommodates clamp-on or bolt-on motors without the need of an adapter (5210)

Specifications:

Manf. Part # 13001

  • Type: Electric hydraulic power tilt and trim PT-130 with gauge
  • Set back: 6"
  • Application: 130 H.P. and smaller motors
  • Trim angle: 20°
  • Total tilt and trim: 90°

Manf. Part # 13002

  • Type: Electric hydraulic power tilt and trim PT-130 without gauge
  • Set back: 6"
  • Application: 130 H.P. and smaller motors
  • Trim angle: 20°
  • Total tilt and trim: 90°

Manf. Part # 52100

  • Type: Electric hydraulic power tilt and trim PT-35
  • Set back: 51/2"
  • Application: 35 horse power and smaller motors
  • Total tilt and trim: 84°
  • Weight: 24 lbs

Manf. Part # 13022

  • Type: Electric hydraulic power tilt and trim transom adapter for clamp motor
  • For use with PT-130 / THT-130C
  • To install small motors with transom clamps
Based On 2 Reviews | Write Review
received CMC power tilt trim unit
by Patrick from Peterborough, Ontario on June 18, 2012
I have not installed the unit yet, but it is everything I expected and should do the job for me. Thanks
(3 of 4 people found this review helpful)
Was this review helpful?
BEST BANG FOR THE BUCK
by Scott from bradenton, Florida on June 03, 2010
Have a 90 hores on a 17ft boat that did not have tt . dealer wanted three times the amount just for parts. the cmc unit is so eazy to install. it took me about one hr to install by myself. every nut and bolt thats needed was there. I have had this on my boat now for about 3 and half years and use the boat atleast 2 times a week."thank god for the weather in fl." and it looks and works just the same today as it did the dad i took it out of the box!! in fact my budy has the same boat and yr. that came with tt and the cmc is twice as fast. and is a real back saver at the end have the day when u dont have to tilt by hand....
(37 of 38 people found this review helpful)
Was this review helpful?
Based On 7 Reviews | Write Review
Its all that
by Flint from Gillsville, Georgia on August 05, 2014
I was skeptical when I ordered the PT-130 tilt trim package. I had read all the reviews and they sounded good but when I installed it and put it to work, I was pleasantly surprised. It really was all it was said to be. The best part is that it performs very well. I would recommend it to any one. Installation was a breeze as well. I had an overhead crane to work with so all I had to do was unbolt the motor, slide the tilt trim in and bolt it up. I was ready to go in an hour. Well worth the money.
(1 of 1 people found this review helpful)
Was this review helpful?
Strong and well made
by Carl from Newport, Washington on July 18, 2013
Very strong and well made. Wiring ready to plug in and mount switch. The only thing I didn't care for was the adaptability to the older style engine with clamps. However, I didn't purchase the adapter plate. I machined my own. Handles my 1987 85 HP very well. Carl, Newport,WA
(2 of 2 people found this review helpful)
Was this review helpful?
Very heavy duty product
by Paul from Waite Park, Minnesota on November 12, 2012
This is a heavy duty product and works as advertised to trim and tilt up to 90°. Installation instructions were good. I was able to install the unit completely on my own. I lifted the 70 HP 1978 Evinrude outboard with a come-along hung from my garage rafters. The standard bolt holes worked. No drilling was required. I used a Jaw Horse to hold the unit up behind the boat. I lifted one end of the Jaw Horse up and then the other end to get the unit onto the bolts. Some of the supplied stainless steel bolts were too long. I was able to cut them off with a 4" grinder with a cutoff blade. It is easy to damage the threads on the bolts. Stainless steel is soft. At one point a nut became stuck on a bolt that was damaged. It could not be reversed. So it had to be cut off. The weather has turned cold and I will not be able to test it in water until spring.
(5 of 5 people found this review helpful)
Was this review helpful?
Great Product
by Merritt from Plymouth, Minnesota on September 21, 2011
Very happy with the quality and ease of installation. Was built better than I expected. Mounted on a 16' duck boat with a 35hp motor. Works fantastic, installed with 2 people in less than 45 minutes. We have used the unit at least 10 times now, no issues what so ever.
(6 of 6 people found this review helpful)
Was this review helpful?
PT-130 Trim and Tilt (No-Gauge)
by Don from Rapid City, Michigan on July 18, 2011
Total installation time was about 2-hrs. 2-men and a fork truck to lift the 75hp motor. Easy instal and works great. Yes I would go this route again.
(4 of 4 people found this review helpful)
Was this review helpful?
48 HP Evinrude
by Danny from Rincon, Georgia on June 26, 2011
48 HP evinrude manual assist tilt was next to impossible to tilt when in the water and fishing tidal water by myself the fear of getting stuck in shallow water. The PT-130 relieved much of that fear and installation was a breeze. I didn't remove any thing from the 48HP and hoisted it up with the ring on the motor and slid it aside then installed the PT130 by myself. The unit is heavy but I was able to put a bolt in the top hole of the boat then align with that hole and loosely attach the PT130. I then lifted the unit and installed the other top bolt, tightened them down and hooked up the power as described in the instructions and raised the unit to install lower bolts. Attached 48Hp to highest location and I get full tilt. Good luck with your install.
(11 of 11 people found this review helpful)
Was this review helpful?
very happy
by Bill from Roff, Oklahoma on June 16, 2011
very happy with power tilt trim and with iboats great service
(6 of 6 people found this review helpful)
Was this review helpful?
Based On 9 Reviews | Write Review
power trim and tilt
by Lynn from Crofton, British Columbia on July 26, 2014
completely satisfied other than shipping costs.
(1 of 1 people found this review helpful)
Was this review helpful?
Just what the dinghy needed
by Stephen from Seattle, Washington on May 10, 2014
This product is a real back saver and it improved performance too!
(1 of 1 people found this review helpful)
Was this review helpful?
tilt and trim
by Cheryl from Portage, Michigan on March 12, 2014
We have not even installed it yet my boat is still covered with snow. We live in Michigan. When we do use it and I am not happy with it I will let you know. I will up date my review when I get it installed and can use it. Thanks
(0 of 4 people found this review helpful)
Was this review helpful?
Boating in the new millennium
by Kevin from Waycross, Georgia on September 28, 2013
I boats had the best price the tilt trim is everything I was hoping for shipped in a timely matter . Thanks I-boats K.White
(2 of 2 people found this review helpful)
Was this review helpful?
great product
by William from Wareham, Massachusetts on June 27, 2013
installed it my self on a 2112 15hp suzuki. no problems installing. been out a few times and it works perfect. the boat is a 2112 Tracker V15 Laker.
(2 of 2 people found this review helpful)
Was this review helpful?
Power tilt and trim
by Martin from Durand, Wisconsin on May 30, 2012
I am very satisfied with this product. It was easy to install and works very well. I would recommend this product to anyone interested in a tilt and trim unit such as this one.
(4 of 5 people found this review helpful)
Was this review helpful?
Great service. The best trader for .. Canada (Quebec)
by Daniel from Saguenay, Quebec on April 28, 2012
Super. Not always easy to order from USA to Canada. I will certainly order again. Customs fees, tax and shipping are reasonable and no hidden charges.The PT-35 works very well. Bye Daniel.
(5 of 6 people found this review helpful)
Was this review helpful?
PT-35 TT
by David from Cedar Rapids, Iowa on October 04, 2011
Excellent product. Works great.
(3 of 3 people found this review helpful)
Was this review helpful?
3 E
by John from Fort Worth, Texas on September 21, 2011
EEE Easy to install-less than 30 minutes Excellent in operation Extra speed Installed on an old 1974 Starcraft 16 ft with a 1984 Evinrude. Added toggle switches up front and on transom. Much quicker up on plane and flatter planing. Highly recommend to one and all.
(20 of 20 people found this review helpful)
Was this review helpful?
Recent Purchase
by John from Mount Joy, Pennsylvania on June 10, 2014
Very pleased with everything
Was this review helpful?
CMC adapter
by Gregory from Kenai, Alaska on August 16, 2012
Was just as picture and packaged great and fast shipping
Was this review helpful?
transom adapter raised motor too high!!!
by Robert from Huffman, Texas on January 19, 2012
After installing my cmc tilt and trim and installing my adapter and even lowering the cmc as low as I could to still mount into wood on the transom (its on a aluminum boat) prop cavitates/blows out. I am not sure how to fix this problem I might could move it down another 1/2 inch but not sure if that would work. I can see this working better on a fiberglass boat but an aluminum boat does not displace that much water. I have had my prop redone with more cup and am going to try and aluminum tail on the motor to see if that helps. Very unhappy,
(1 of 1 people found this review helpful)
Was this review helpful?
tilt,trim and adapter
by Kenneth from Dayton, Texas on September 24, 2011
This system is working great with no problems. Easy to install and modify to fit any motor. Thanks for a great product.
(3 of 3 people found this review helpful)
Was this review helpful?
Ask a question for
Question & Answer Guidelines
This product ships in 1 business day.

Add to Cart and enter your Postal Code to determine the shipping charges and estimated delivery date.
* Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies