H-Leg and Sockets ONLY - Garelick
Price: $57.66
Save: $14.33
(19% Off $71.99)
Part # 75014
2nd Day Air for $2.99 More Eligible
Hardware and H-Leg - Garelick
Price: $82.15
Save: $17.84
(17% Off $99.99)
Part # 75055
2nd Day Air for $2.99 More Eligible
SHIPS TOMORROW!* if ordered in 21 hrs 35 mins.


  • Aluminum support arms attach to bottom of seat or table
  • Folding brackets attach to side of boat
  • Gives added support. Allows seat or table to fold against bulk head or coaming
  • Stanchion legs fit sockets under seat or table

75014 : H-Leg and Sockets ONLY
75055 : Hardware and H-Leg (H: 32" (81cm) includes two mounting sockets)

Technical Documentation

Mounting Instructions for Seats with Folding Helmsman Hardware and Side Mount Helmsman Seat Hardware
Mounting Instructions for Model 75005 Side Slide and Model 75008 Side Slide with Mounting Hardware
Mounting Instructions for Model 75055 Side Mount Helmsman Seat Hardware with H-leg; Model 75014

Features and Compatibility

Mounting Instructions for Model 75055 Side Mount Helmsman Seat Hardware with H-leg; Model 75014

Mounting Information
NOTE: This product uses locknuts for a secure assembly. Locknuts thread on harder than conventional nuts and require a screwdriver and wrench for attachment.

Tools Required

  1. Screwdriver
  2. Crescent wrench adjustable to 7/16"
  3. Drill

Mounting Guidelines
For best utilization of your helmsman seat, it is recommended that the seat be mounted:

  • As high as possible to enable a clear view over the bow.
  • As close as possible to the wheel, leaving just enough room to slide onto the seat from the side (see Fig. 1).

Mounting Instructions for Model 75055

  1. Position seat on port or starboard bulkhead of boat so it will conform to the Mounting Guidelines given above. Mark a line on the bulkhead where the seat bottom is positioned (see Fig. 1). Make certain that the line is:
    1. no higher above the deck than the stanchion leg's measured length;
    2. parallel to the deck's surface;
    3. located on a good, solid surface suitable for mounting.
    4. NOTE: This line will be used to position U-brackets (A) in step 8.

Seat Position

  1. Refer to Fig. 2 and position both support brackets (B) on the bottom of the seat so that:
    1. Support bracket is allowed to extend a minimum of 1" from seat bottom (However, make certain that all screw holes are located on the seat bottom.);
    2. Brackets are spread apart from each other on seat bottom for maximum support and stability;
    3. Bracket's centerlines are parallel to each other. This will allow proper hinging action.
    4. NOTE: It is allowable to mount support brackets over the hinge on the seat bottom for correct positioning.
  2. Mark the bracket's hole locations on the seat bottom and drill all with a 1/8" bit.
  3. Secure the brackets to the seat bottom by aligning the holes and using screws (C).
  4. Snap both socket castings (D) over grooved ends of H-leg (E).

Bottom View

  1. Position socket castings (D) with H-leg (E) attached on seat bottom so they are centered on the seat's side and at least 2" from the edge. Make sure that the flat side of the sockets face toward the mounted support brackets (see Fig. 2). Mark both socket's mounting holes and drill them with a 1/8" bit. Secure both castings in position with 8 screws (C).
  2. Attach the 2 U-mounting brackets (A) to support brackets (B) by aligning their holes and inserting bolts (F) as in Fig.
  3. Secure with locknuts (G). Finger-tighten only. These nuts will have to be removed in step 9.
  4. Position the attached U-mounting brackets (A) against the line drawn in step 1. Mark the bracket's hole locations on the side bulkhead and drill all 4 holes with a 1/8" bit (see Fig. 3).
  5. Remove the 2 U-mounting brackets from the support brackets and align them with the drilled holes on the side bulkhead. Secure with 4 screws (C).

Mounting Hardware

  1. Attach seat to boat by aligning support bracket's and U-mounting bracket's holes, inserting bolts (F) and securing with locknuts (G) as in Fig. 3.
  2. Insert the grooved ends of H-leg (E) into both socket castings mounted on seat. Check to see that seat bottom is parallel to deck surface (see Fig. 4). If not, cut off the appropriate length of tubing on opposite end with a hacksaw. Slip polytips (H) on ends of H-leg. NOTE: Tips will go on easier by heating in warm water.
  3. If fore and aft adjustment of seat is desired, then seat may be adapted by using model 75005 Side Sliding Assembly.
Mounting Instructions for Model 75014
Follow steps 5, 6 and 11 of the above instructions for mounting. NOTE: Screws (C) not provided.

Seat Height

Average Customer Review for Hardware and H-Leg - Garelick
Full StarFull StarFull StarHalf StarEmpty Star
Based On 3 Reviews | Write Review
Full StarFull StarFull StarFull StarEmpty Star
by Frank from Somerset, Massachusetts on August 01, 2014
What I prided for
(0 of 1 people found this review helpful)
Was this review helpful?
Full StarFull StarEmpty StarEmpty StarEmpty Star
Wrong Hardware
by Heath from St. Clair Shores, Michigan on September 01, 2013
I ordered two sets and the mounting hardware for the legs do not match. Different sizes and material.
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
Garelick seat hardware
by John from Spokane, Washington on May 12, 2013
The product is of high quality construction and was well packed. I would have no hesitation in recommending this product and the service provided by iboats.com was excellent. Quick delivery and good prices.
(1 of 1 people found this review helpful)
Was this review helpful?
What is the width of the H-Leg?
9-3/16" inside width. 11-3/16" outside width.

What is the height of the leg?
H: 32" (81cm)

Ask a question
Question & Answer Guidelines
This product ships in 1 to 5 business days.
Add to Cart and enter your Postal Code to determine the shipping charges.
Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies