Hot Shot T-Top Boat Cover (Fits 23'5" to 24'4" Length, 102" Width w/o Bow Rails, Single Engine Cut-Out)
The iBoats Experience
Boats for SaleBrowse thousands of constantly-updated listings and search by location, brand, and boat type See more...
AdviceConnect with our expansive community and tap into the knowledge base of the most dedicated boaters around. See more...
Shop ProductsBrowse and search for hundreds of thousands of boat parts, accessories, and supplies to suit your every need.
The three main features of these covers are:
- 1. Bow and stern sections are separated into two halves.The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. The stitching of the zippers into the cover halves feature beginning each zipper at the top of the console tube and ending at the hem (finished outside edge). This allows installation of the cover by a single person inside the boat.
- 2. The "console tube" or center portion of the cover fits over the console and under the T-top.Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of the console tube incorporates an adjustable draw rope in both front and rear sections. The draw ropes tighten the tube from side to side around the T-top verticals and also are used to secure the tube to the upper horizontal supports of the T-top. The "console tube" is not a perfect rectangle as it comes up off the cover halves. Rather it is more trapezoidal in shape and wider at the base than at the top. This feature allows these covers to fit and function properly even though there are variations in size and position of the T-tops within the confines of the hull and deck.
- 3. Tie down system in the hem or perimeter of the covers.To relieve stress on the zippered ends during over the road trailering Taylor Made has added a webbing strap and quick release buckle to the cover at both sides just above the zipper to facilitate the installation of the cover by a single person. The rope that spans the perimeter of the cover is made into two sections. The first goes from one side at the zipper opening, around the bow to the same point on the opposite side. The second goes around the stern of the boat in a similar fashion.
Please be careful when ordering this product, it has limitations that differ from our General 30-day Return Policy. After all, we want you to be satisfied with your order so you'll return again and again as an iboats.com customer, and to also recommend us to your boating friends
- Semi-Custom Boat Covers
Semi-custom covers are "made-to-order" and are thus specific to your order. However, we understand that sometimes a product you purchase just doesn't work out, which is why we want to make the return process as easy as possible for you. After all, we want you to be satisfied with your order so you'll return again and again as an iboats.com customer, and to also recommend us to your boating friends.
A made-to-order semi-custom cover may be returned within the first 30 days after shipment, but is subject to a 15-25% restocking fee. Odd-Lots, Liquidations, In-Stock Specials, Closeouts and customer requested alterations are non-returnable unless an error was made by iboats.com or by the boat cover manufacturer.
Merchandise must be in new, unused condition with all original packaging in good condition; plus parts, accessories, manuals, and/or warranty cards included. You will need to receive a return authorization number (RA #) as well as instructions from our Customer Service Department.
Please note that each boat cover manufacturer may have additional requirements concerning product returns or warranty claims, including but not limited to: restocking fees, shipping fees, or product order change fees.
Because boat covers are "made-to-order", there will be a $25-$50 fee for any boat cover order cancellation after 1 business day of purchase, as the cover has already gone into production.Warranty Policy
30 days after the purchase date, the manufacturer of the product(s) will need to be contacted for a warranty claim.Returns for Canadian Customers
Canadian customers, please be careful when placing your order; iboats.com does not accept any return merchandise on Canadian orders unless the merchandise you received was defective, damaged, or an error was made by iboats.com. In such cases, please contact iboats.com Customer Service within 30 days of the original shipping date for a return authorization number. Returned items that do not have a RA # will not be accepted.