Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
Fiberglass Bottomkote Classic is a hard modified epoxy, fast dry antifouling paint with clean stable colors that has been developed to provide effective season-long
protection on all power and sailboats. The fast dry formula allows the boat to be painted and launched in the same day. Fiberglass Bottomkote Classic is
recommended for use on the underwater areas of fiberglass, wood, and properly
primed metal (except aluminum) boat hulls. It can be used in fresh, salt and
brackish waters.
Application Temperature: 50°F (10°C) and above air and hull
Coats Required: 2 coats minimum
V.O.C.: Less than 470 gms/ltr as supplied (3.92 lb/gallon)
Recommended Application Systems
Compatibility
Fiberglass Bottomkote® Classic can be applied over most other antifouling paints provided the old coating is tightly adhered, is in sound condition and has been thoroughly sanded with 80 grit wet-or-dry sandpaper.
Preparation Previously Painted - Good Condition: Remove all traces of loose paint and contamination by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Interlux Special Thinner 216. Apply at least 2 coats of Fiberglass Bottomkote Classic.
Previously Painted - Poor Condition: Completely remove all old antifouling paint, using Interlux® Interstrip
299E for fiberglass, and wood, and by sandblasting to near white metal for steel. Follow application systems below.
Bare Fiberglass: It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using Interlux All-Purpose Boat Soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow
to dry. Remove mold release wax using one of the following Interlux products. Fiberglass Surface Prep YMA601
or Fiberglass Solvent Wash 202 following the product label instructions. To be certain that all of the contamination
has been removed, run water over the surface. If the water beads up or separates, clean again. When the water
sheets off, all contamination has been removed. Fill any surface imperfections with Interlux Watertite YAV135,
Interfill® 830 or Interfill 833 following the label instructions. After the surface has been properly cleaned, proceed with one of the application systems below.
Application Systems Bare Fiberglass - No Sand System: Clean the surface following the preparation procedure above. Apply one
coat, of Interlux InterProtect® 2000 or Fiberglass No-Sand Primer YPA200 following the label instructions for
applying the primer and overcoating with antifouling paint. Apply two coats of Fiberglass Bottomkote Classic,
allowing for the appropriate dry times.
Bare Fiberglass - Sanding System: Clean the surface following the preparation procedure above for bare
fiberglass. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding
residue off the surface with Fiberglass Solvent Wash 202. Sand and wipe clean. Apply two coats of Fiberglass
Bottomkote Classic allowing for appropriate dry times.
Bare Fiberglass - Blister Prevention System: Apply the InterProtect system for the prevention of blisters.
Bare Wood: Sand the entire surface with 80-grit sandpaper. Wipe the sanding residue off the surface with Special
Thinner 216. Apply the first coat of Fiberglass Bottomkote Classic thinned 10% with Special Thinner 216 or Brush-
Ease 433. Fill seams with Interlux Seam Compound 30 (if necessary). Apply two more coats of Fiberglass
Bottomkote Classic unthinned, allowing for the appropriate dry times.
No Review for Fiberglass Bottomkote Classic Boat Paint, Red, Gallon - Interlux
This product typically leaves our warehouse in 1 business day.
To determine the shipping cost and estimated delivery date for this item click Add to Cart, then click Calculate Shipping inside your shopping cart.
General Policy
We work hard to provide you with the best value in product prices and shipping charges, and to get your order to you in a timely, safe, and convenient manner. Internet sales involve the cost of getting the product to you, and shipping carriers base that cost on the size and weight of the package, plus the distance the package travels from our warehouse to your door. We keep our product prices low, negotiate low shipping charges from our carriers and pass those savings on to you, and we don't charge sales tax (except for residents of Utah), so your order from iboats.com is the best value for all your boating needs.
Our standard shipping method is UPS ground, which typically takes 2-5 additional transit days after the order has left our warehouse, depending on your delivery address. We also offer other shipping options, including expedited delivery, and the actual delivery date will depend on the shipping options you choose.
Shipping to Canada
Most products sold by iboats.com can be purchased and shipped to Canada. Some restrictions apply to certain items, such as hazardous materials, over-weight products, and the method of shipping. Available product lines, shipping rates and fees may vary depending on the delivery address for your order.
Currently, iboats.com offers ground shipping to all Canada provinces. Our Canadian brokerage service accelerates your orders through the Customs clearance process and facilitates the delivery of your order through Canada Post or the best method based on your shipping address. We do not currently offer expedited shipping methods to Canada.
At iboats.com we want to simplify your transaction and give you a pleasing purchasing experience so you'll come shop with us again and again. We therefore calculate all the duties, taxes, and other fees specific to Canadian orders and show you the total landed cost of getting the order to your door. There are no hidden fees and will be no surprise COD charges when the package is delivered to you.
Order History & Tracking
We provide several methods to track your order and keep you informed of your order status and expected delivery date. After completing an iboats.com purchase transaction, an account will automatically be created for your provided email address. You'll receive an email from iboats.com Customer Service informing you of your new User Account and the many benefits it provides. If you don't wish to have an iboats.com Account with password, do nothing and your account won't be registered; however, you can respond to the instructions in the email and easily register your account and setup a password. This will allow you to sign in to your account by choosing the Order Status link from any iboats.com page, where you can browse your order history and track the status of all your orders - tracking numbers are displayed that link to the delivery carrier's tracking webpage.
If you have provided your email address during checkout, we will also email you your invoice, which includes a link for tracking your order and viewing the current status of your order. Refer to your invoice email and tracking link any time you wish to track the status of your order
Return Policy
We're here to help! We understand that sometimes a product you purchase just doesn't work out, which is why we want to make the return process as easy as possible for you. After all, we want you to be satisfied with your order so you'll return again and again as an iboats.com customer, and to also recommend us to your boating friends.
Unless specified otherwise, an item(s) may be returned within the first 30 days after the item(s) is shipped to you. Merchandise must be in new, unopened and unused condition with all original packaging in good condition; plus parts, accessories, manuals, and/or warranty cards included. You will need to receive a return authorization number (RA #) as well as instructions from our Customer Service Department.
If needed, we recommend starting your return online to receive a Return Authorization Number(RA #). Returned items(s) that do not have an RA # will not be accepted.
Warranty
iboats.com has a 30-day return policy. After 30 days of your purchase, the manufacturer of the product(s) will need to be contacted for a warranty claim. If you need assistance finding the manufacturers number please contact our Customer Service Department.
Returns for Canadian Customers
Canadian customers, please be careful when placing your order; iboats.com does not accept any return merchandise on Canadian orders unless the merchandise you received was defective, damaged, or an error was made by iboats.com. In such cases, return the merchandise within 30 days of the original shipping date for a full refund.
iboats.com Low Price Guarantee – Quick and Simple
We have the best selection of products at the best prices, guaranteed.
Nobody beats our prices. If you find a current lower price on an identical, in-stock item from any nationally recognized marine Internet retailer, we will match the price. iboats.com works hard to bring you everyday low prices plus knowledgeable product advice, great in-stock selection, and outstanding customer service. Our guarantee covers it all, and if you’ve found a better price let us know and we’ll match it and work hard to make you a satisfied iboats customer for life.
Quick: Call 1-800-914-1123
Simple: Have the lower competitive price info ready, as outlined below.
Buy with Confidence – We Won’t Be Beat!
Here’s what you need to supply us to verify a lower price:
The retailer’s name and URL website address of where you found the lower price.
The product name, manufacturer, model number, price, and shipping charges.
Electronics products, trolling motors, and outboard engines are not available for price matching.
30-day Guarantee
Buy now with confidence, knowing that should there ever be a lower price from any nationally recognized U.S. marine Internet retailer for 30 days after your purchase, iboats will match that price and refund you the difference. Or we’ll match the price before your purchase. The price considered will be the advertised price plus shipping and handling charges.
Qualifying items must be verifiable on the Internet or through a current printed advertisement. Items must be identical, in-stock new products and not sold through a membership club or auction site or any of the following offers, such as free offers, multiple discounts like “buy one, get one at half off”, special orders, special bundles, clearance sales, mail-in rebate offers, typographical errors, private sales, non-retail websites, promo discounts, or limited-time offers. All price matching is at the discretion of iboats.com and is subject to change at any time. iboats reserves the right to limit quantities. Price-match products are not eligible for special offers or discounts.
iboats.com – The Leader in Price Buster Confidence!
Please be aware of the following order dates below to have your items have the best chance of delivery by December 24. Shipping options apply to in-stock items only, and not made-to-order products such as boat covers and bimini tops. Mail handlers are extremely busy this time of year, therefore we cannot guarantee delivery before Christmas of any items. For the most up-to-date shipping information, please refer to the estimated delivery time specified in the shopping cart and checkout process.
