Interprotect® 2000 (Interlux)

Interprotect 2000E, Cure, Gallon - Interlux
Your Price: $67.14
Save: $11.85
(15% Off $78.99)
Part # Y2001E/1 ValueShip™ Eligible
No Reviews | Write Review | Ask Question
Interlux
Features:
  • For use in prevention of and repair of osmotic blistering
  • Two-part epoxy water barrier with Micro-Plates
  • Up to two weeks is allowed between coats of InterProtect 2000E
  • Fast drying, easy application
  • Sag resistance to insure the elimination of sags and runs during application

InterProtect® 2000E is a unique two-part epoxy designed to reduce the potential of water absorption by fiberglass hulls. InterProtect is unique among epoxies because it has Micro-Plates®, a protective barrier within its film to slow down water permeation. Technically, InterProtect Micro-Plates provide millions of overlapping microscopic plates that create a barrier similar to shingles on a roof. These overlapping Micro-Plates eliminate any direct path for water migration and also improve the sag resistance of the epoxy making application easier.

InterProtect has been the product of choice for Boat Builders and Repair Yards since 1985.

Prevention is Better Than Cure
The importance of having a moisture-free hull cannot be overemphasized. The drier the laminate, the lighter the hull, the better the performance, the more efficient fuel use and the longer the gelcoat life. A boat hull that has absorbed moisture will also sit lower in the water than intended and will reduce the responsiveness of the boat.

The InterProtect® System was designed to repair hulls which have experienced gelcoat blistering. However, the best time to attack hull blistering is before it happens.

Taking preventative action before a problem occurs will greatly reduce the likelihood of an expensive repair and increase resale value. If you're buying a new boat, protect your investment with the InterProtect® System before it ever goes in the water!

InterProtect® is a unique two-part epoxy designed to reduce the potential of water absorption by fiberglass hulls. InterProtect® is unique among epoxies because it has Micro-Plates®, a protective barrier within its film to slow down water permeation. Technically, InterProtect® Micro-Plates® provide millions of overlapping microscopic plates that create a barrier similar to shingles on a roof. These overlapping Micro-Plates® eliminate any direct path for water migration and also improve the sag resistance of the epoxy making application easier.

Important Steps in the Repair of Gelcoat Blisters
1 Proper Preparation of the Gelcoat
This includes getting all of the antifouling paint off and removal of as much gelcoat as necessary to get the hull dry (i.e. the entire gelcoat or just small areas). A professional, who has looked at your boat, should make this determination.
2 Drying of the Hull
This is the most critical step in the process. If you do not get the hull dry it will re-blister. We recommend a comprehensive washing and drying procedure.
3 Application of Epiglass® HT9000 Resin
This solventless epoxy seals up the laminate and fills any cloth that has been voided of resin. This should be done before using fillers to fill the voids.
4 Application of Interprotect® 2000E or Interprotect® 3000
These epoxies are used as a water barrier to minimize the possibility of reoccurrence of damage.

Recommended Overcoating Intervals
Temperature Time Between Coats of Interprotect® 2000E** First Coating of Antifouling
Min.*** Max. Min.*** Max
50°F 5 hrs 2 weeks 7 hrs 9 hrs
50°F 4 hrs 2 weeks 6 hrs 8 hrs
50°F 3 hrs 2 weeks 5 hrs 7 hrs
50°F 2 hrs 2 weeks 3 hrs 5 hrs
Number of Coats* 4/5 1
*It usually takes 4-5 coats of InterProtect® 2000E/2001E but the final film thickness of 10 mils D.F.T. is more important than the number of coats. See page 28 for amount needed.
**If you exceed the maximum dry times between coats of epoxy you must sand with 80 grit and apply at least one more coat of InterProtect® 2000E/2001E to ensure having 10 mils D.F.T.
***Overcoating times will vary due to wide variations in temperature and humidity. The best method to determine when the InterProtect® 2000E is Ready-to-Overcoat is to check the paint film using the 'Thumb Print' test. If the InterProtect® 2000E feels tacky and you can leave a thumbprint in the paint film without getting any paint on your thumb it is ready for overcoating. Test the paint film 1 hour after starting the application. Continue testing every 15 minutes using the 'Thumb Print' test until reaching the ready-to-overcoat stage. Immediately, begin to apply the Interlux® antifouling paint once the primer has reached the Ready-To-Overcoat stage. Do not use this method with Epiglass® Epoxy or InterProtect® 3000. These times do not apply to VC® Offshore or Baltoplate, Micron® Optima or Fiberglass Bottomkote® Aqua.

How much InterProtect® 2000E/2001E do I need?
It is the best to actually measure the wetted surface area of the hull. If this is difficult to do, a close approximation can be made by multiplying the length overall, times the beam, times 85% (L.O.A. x Beam x .85 = wetted surface area). Divide the wetted surface area by 60 for brush and roller applications and by 45 for spray application. The resulting number is the number of gallons that need to be applied to reach a 10 mil dry film thickness.

Disclaimer: Charts apply to Interlux products only. The information provided is not intended to be exhaustive. Because iboats.com does not know how this information is being used, they cannot take responsibility for any actions as a result.

The performance of marine paint on many factors outside the control of iboats.com, including surface preparation, proper application, and environmental conditions. Therefore, iboats.com cannot guarantee this product's suitability for your particular purpose or application.

By purchase or use of this product, buyer agrees that the sole and exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at iboats.com's option.

Ask a question for
Question & Answer Guidelines
This product ships in 1 business day.

Add to Cart and enter your Postal Code to determine the shipping charges and estimated delivery date.
* Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies