- For dry sailed boats or boats stored in non-fouling fresh water.
- Can be buffed to give a high gloss, ultra smooth surface.
- Suitable for use on fiberglass, wood and steel hulls
- Excellent for trailered boats.
Non-antifouling racing finish. Tough, smooth synthetic alkyd enamel. For use when boat is dry-sailed or stored in fresh water. Buff for high gloss, ultra-smooth surface.
1959 Hard Racing Copper Bronze is recommended for use in fresh water on racing hulls, sailboats, runabouts or cruisers. It is a non-antifouling hard racing finish that can be buffed to give a high-gloss, ultra-smooth surface.
1959 Hard Racing Copper Bronze is recommended for use in fresh water on
racing hulls, sailboats, runabouts or cruisers. It is a non-antifouling hard
racing finish that can be buffed to give a high-gloss, ultra smooth surface.
It can be used in saltwater for small, dry sailed boats which are not left in
the water. When used above the waterline in saltwater, the 1959 Hard
Racing Copper Bronze will oxidize to a green color if not overcoated with a
clear sealing coat. 1959 Hard Racing Copper Bronze may be applied over
most aged hard racing non-antifouling coatings. If the old paint type is
unknown, sand a small area and apply a test patch of 1959 Hard Racing
Copper Bronze to test its compatibility with the old paint. If the 1959 cracks
or lifts the old paint, all the old paint will have to be removed. If nothing
appears to happen when the 1959 is applied, let the test patch dry overnight,
then scrape the 1959 to see if it is adhering to the old paint satisfactorily.
If the adhesion looks good follow the recommendation for Previously
1959 Hard Racing Copper Bronze is loaded with copper flake pigment. As a
result of this there is a tendency for settling to occur, especially if the paint
has been on the shelf for several months. It is necessary to thoroughly mix
the paint before using. If possible shake the can of paint on a mechanical
paint shaker. Before using check the sides and bottom of the can to make
sure all the pigment has been mixed in. If mixing is going to be done with a
wooden paddle or an electric drill mixer, pour off half of the liquid from the
top of the can into another can and then properly mix in any settled pigment;
then remix the two parts together thoroughly.
Adhere to all application instructions, precautions, conditions and limitations
to obtain optimum performance. Refer to individual labels and tech sheets
for detailed instructions when using associated products, etc. Do not thin
1959 Hard Racing Copper Bronze more than 5% (6.4 ounces per gallon) or
inadequate paint film thickness will occur and premature erosion of the
finish will be likely.
Coating performance, in general, is proportional to the degree of surface
preparation. Follow recommendations carefully, avoiding shortcuts. Inadequate
preparation of surfaces will virtually assure inadequate coating
Vehicle Type...Oleoresinous Varnish
Method...Brush, Roller, Airless or Conventional Spray
Number of Coats...2
Dry Film Thickness per Coat...0.75 mils (1.75 wet mils)
Thinners...120 Brushing Thinner, 121 Spraying Thinner
Previously Painted Surfaces: If the previous coating is in good condition, thoroughly sand with
80 grit production paper and wipe clean with a rag dampened with Pettit 120 Brushing Thinner to
remove sanding residue. Apply two coats of 1959 Hard Racing Copper Bronze observing the
proper dry times. If the previous coating is soft or in poor condition, remove to the bare surface
by sanding or using Marine Grade Bottom Paint Remover 9050. Proceed with the appropriate bare
system as described below. Old tin copolymer paints must be removed before applying 1959.
Bare Fiberglass: All bare fiberglass, regardless of age, must be thoroughly cleaned using 95
Fiberglass Dewaxer and clean lint-free rags. Several cleanings may be necessary to ensure complete
removal of contaminants. Change rags frequently during the dewaxing/cleaning process to
ensure complete removal of contaminants rather than merely smearing them on the surface. New
boats must be scrubbed with a detergent and water solution and rinsed with fresh water prior to
dewaxing. After the surface has been dewaxed, sand it thoroughly with 80 grit production paper
and rewash the sanded surfaces with 95 Dewaxer or 120 Brushing Thinner to remove sanding
residue. Apply one coat of Pettit Protect 4700/4701 High Build Epoxy Primer. When thoroughly
dry, sand with 80 grit paper and wipe clean again. Apply two coats of 1959 Hard Racing Copper
If sanding is prohibited, as with certain vinyl-ester gelcoats, or is otherwise impractical, make sure
the surface has been completely and thoroughly dewaxed and cleaned with Pettit 95 Fiberglass
Dewaxer. Then apply one, thin, continuous coat of Pettit 6999 Sandless Primer. Topcoat with two
coats of 1959 carefully following the topcoating instructions on the Sandless Primer label.
Bare Wood: Sand the entire surface with 80 grit production paper and wipe clean with a rag
dampened with Pettit 120 Brushing Thinner. Apply a coat of Pettit 6627 Tie Coat Primer thinned
25% with the 120 Brushing Thinner to penetrate and seal the wood. Fill any open seams with
Pettit Seam Compound (7110 White or 7610 Mahogany) and allow to dry overnight. Apply two full
coats of 1959 observing the proper dry times.
Steel Hulls, Underwater Metal Parts and Keels: For steel hulls and metal keels, wash the
surface with Pettit 120 Brushing Thinner to remove any oil film or grease. The metal should be
abraded with emery cloth to a bright texture. Remove all sanding residue by vacuuming or with
clean, compressed air. Apply one, thin wet coat of Pettit 6455 Metal Primer; allow to dry at least
two hours and then apply two coats of Pettit 6627 Tie Coat Primer followed by two coats of 1959
Hard Racing Copper Bronze.
DO NOT USE THIS PRODUCT ON ALUMINUM HULLS OR OUTDRIVES.
Disclaimer: Charts apply to Pettit products only. The information provided is not intended to be exhaustive. Because iboats.com does not know how this information is being used, they cannot take responsibility for any actions as a result.
The performance of marine paint on many factors outside the control of iboats.com, including surface preparation, proper application, and environmental conditions. Therefore, iboats.com cannot guarantee this productís suitability for your particular purpose or application.
By purchase or use of this product, buyer agrees that the sole and exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at iboats.comís option.