Pettit/ Z-Spar Topside Enamel Paint

Z-Spar Topside Boat Enamel, Semi-Gloss, White, 1 Gallon - Pettit (Kop Coat) - Pettit Paint
Your Price: $70.66
Save: $51.33
(42% Off $121.99)
Part # 101G
No Reviews | Write Review
Pettit Paint

Z*Spar is an excellent initial gloss, high gloss retention, and overall long life. Brushes beautifully without brush marks. Self-leveling qualities give glass like finish.

Z*Spar Enamel is a traditional modified long oil alkyd of exceptional all-around durability. Famous for extraordinary gloss and gloss-retention. #99 Solid Coat contains a very high loading of titanium dioxide for maximum hiding power. Z*Spar Enamel is a superb finish for all topside surfaces of wood, metal or fiberglass.

All paint colors shown here are for guidance only. Due to differences in screen displays that are beyond our control, the colors on these pages cannot be guaranteed to match the actual color in the can.

Physical Data
Finish Type...Alkyd Topside Finish
Components...1
Coverage...500 sq. ft. per gallon; 125 sq. ft. per quart (allows for an approximate loss of 20%).

Application Data
Method...Brush, Roller or Spray
Number of Coats...2
Dry Film Thickness per Coat...1.5 mils (3 wet mils)
Thinners...Use Z*Spar T-8 for spray. Use Z*Spar T-10 or T-11 for brush application.
Cleaner...T-8, T-10 or T-11

Surface Preparation
Prior to application, surfaces to be painted must be free of all dirt, peeling paint, rust, oil, grease, wax and other interfering materials.

Fiberglass: Wash with soap, ammonia and water. Let dry, then clean thoroughly with Z*Spar T-1132 Fiberglass Prep Solution. Sand with 220 grit sandpaper. Clean off sanding dust thoroughly by vacuuming and/or airblasting followed by wiping with a clean tac-rag. If surface is slightly rough or porous, prime with Z*Spar 105 White Undercoater.

Old Paint All existing painted surfaces in good firm condition should be lightly sanded. All existing paint in poor condition (cracked, blistered, peeling) must be removed and surfaces treated as new.

New or Bare Wood: Surfaces must be sanded with 180-220 grit sandpaper. Remove sanding dust by vacuuming and/ or airblasting followed by wiping with a clean tac-rag. Surfaces should then be sealed with Z*Spar S-120 Clear Sealer. After the sealer has dried, apply one coat of Z*Spar 105 White Undercoater. Sand undercoater with 220 grit sandpaper before applying Z*Spar Topside Enamel.

Aluminum: Sand with 180-220 grit sandpaper. Clean off sanding dust before applying paint. Apply one coat of Z*Spar P-707 Prime-All Primer before applying Topside Enamel. Z*Spar 105 White Undercoater can be used over P-707 Prime- All Primer for smoothing surfaces if desired.

Steel: Surfaces must be well sandblasted or sanded to remove all millscale and rust. Then apply 2 coats of Z*Spar P- 646 or 340 Gold Epoxy Primer. Z*Spar 105 White Undercoater can be used over P-646 or 340 Gold for smoothing surfaces if desired. NOTE: When removing sanding dust from a sanded surface, DO NOT use thinner solvent, gasoline or a dirty rag. DO use a tac-rag, vacuum, air blast or a clean dry cloth. NOTE: If filling or fairing of nonsubmerged surface is required use #1 or #2 White Glazing Putty after the first coat of 105 White Undercoat.

Application: Brush, roller, conventional or airless spray. For brush application reduce with approximately 5-10% T-10 Thinner, or T-11 Thinner in excessively hot weather and apply in full wet coats. For spray application thin with 15-20% T- 8 Thinner and spray on two coats approximately 15-20 minutes apart. The first coat should be a light coat and the second coat should be a medium coat. If the second coat cannot be applied within 20 minutes, allow an overnight dry between coats. An alternate spray method would be to apply two full coats allowing a 24 hour drying time between coats and sanding with 280-320 grit sandpaper prior to the final coat.

Disclaimer: Charts apply to Pettit products only. The information provided is not intended to be exhaustive. Because iboats.com does not know how this information is being used, they cannot take responsibility for any actions as a result.

The performance of marine paint on many factors outside the control of iboats.com, including surface preparation, proper application, and environmental conditions. Therefore, iboats.com cannot guarantee this product's suitability for your particular purpose or application.

By purchase or use of this product, buyer agrees that the sole and exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at iboats.com's option.

bait and switch by McKie - Santa Fe, New MexicoNovember 06, 2011
I ordered one gallon of Z-spar Solid Gloss White, at the advertised price. I received an invoice clearly stating that I was billed for and would receive a gallon. I received a quart, not a gallon. I complained, and was told there'd been a mistake on the pricing, so I was only sent a quart. I-boats had every opportunity to inform me of any mistake before shipping, but they didn't - they just shipped the quart. Surprise! Foul play by I-boats. They've lost my future business.
(2 of 2 people found this review helpful)
Was this review helpful?
Z-SPAR GLOSS WHITE ENAMEL by Richard - Villa Hills, KentuckySeptember 28, 2011
Has to be among one of the greatest marine paints available... makes a novice effort look like a pro!
Was this review helpful?
This product ships in 1 business day.

Add to Cart and enter your Postal Code to determine the shipping charges and estimated delivery date.
* Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies
Great Boating Days are Ahead!
Enjoy Extra Discounts 5-20% Off During the SPRING SAVINGS SALE!
Great Boating Days are Ahead!
Enjoy Extra Discounts 5-20% Off During the SPRING SAVINGS SALE!