The Ice Eater is designed to prevent ice from forming around boats, marinas, docks, and piers as well as effectively melting existing ice by breaking the surface with a continuous current of warmer bottom water.
Ice Eater's propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation.
Ice Eater will melt existing ice. Unlike other de-icing units, Ice Eater requires no additional hardware in order to obtain the desired de-icing pattern. Ice Eater is shipped complete with suspension lines. It can be taken out of the box, hung in place and plugged in.
Ice Eater may be hung from a pier or boat. Two to three feet is the average operating depth.
 |
Powerhouse 1/2HP Ice Eater
Part # P500-25-115V
- 1/2 H.P. energy efficient high quality motor with 28 pounds thrust
- 5.0 amps, 115 volt, one phase, 60/50 cycle
- 25 foot quick change power cord
- Two 25 foot x 3/8 hollow braided mooring lines with shackles
- Dimensions of shipping box 12 5/8 x 12 5/8 x 12 3/4
- Weight 36 pounds
- Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water; Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified
- Motor shaft is 316 stainless steel, the best material for salt water application
- Permanent split capacitor ensures quick high torque and smooth operation, while producing the highest efficiency of a single phase induction motor; Motor and capacitor are matched for ultimate performance
- Internal, heavy duty, hard faced mechanical seal with stainless components immersed in dielectric lubricating fluid; Additional double lip shaft seal for extra protection
- Stator motor windings have double impregnation of baked insulating varnish
- Two heavy duty ball bearings provide support for the rotor while being cooled with dielectric type oil
- Sacrificial custom designed zinc is provided for conditions where electrolysis may be present
- Propeller is custom designed for maximum thrust and performance; Propeller screws on shaft for easy removal and replacement
- Twenty-five feet of 16/3 water and oil resistant cord with three prong molded plug is standard; Additional length cord available: 50 and 100 feet
- Heavy duty PVC custom brackets that attach motor to shroud; All stainless bolts and locking aircraft nuts are used
- Performance certified tested at our facility for proper output and leaks before shipment
- Best three-year limited warranty in the marketplace
- Comes complete, just open the box, remove and install
|
 |
Powerhouse 3/4HP Ice Eater
Part # P750-25-115V
- 3/4 H.P. energy efficient high quality motor with 36 pounds thrust
- 4.7 amps, 115 volt, one phase, 60/50 cycle
- 25 foot quick change power cord
- Two 25 foot x 3/8 hollow braided mooring lines with shackles
- Dimensions of shipping box 14 1/2 x 14 1/2 x 16 1/8
- Weight 45 pounds
- Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water; Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified
- Motor shaft is 316 stainless steel, the best material for salt water application
- Permanent split capacitor ensures quick high torque and smooth operation, while producing the highest efficiency of a single phase induction motor; Motor and capacitor are matched for ultimate performance
- Internal, heavy duty, hard faced mechanical seal with stainless components immersed in dielectric lubricating fluid; Additional double lip shaft seal for extra protection
- Stator motor windings have double impregnation of baked insulating varnish
- Two heavy duty ball bearings provide support for the rotor while being cooled with dielectric type oil
- Sacrificial custom designed zinc is provided for conditions where electrolysis may be present
- Propeller is custom designed for maximum thrust and performance; Propeller screws on shaft for easy removal and replacement
- Twenty-five feet of 16/3 water and oil resistant cord with three prong molded plug is standard; Additional length cord available: 50 and 100 feet
- Heavy duty PVC custom brackets that attach motor to shroud; All stainless bolts and locking aircraft nuts are used
- Performance certified tested at our facility for proper output and leaks before shipment
- Best three-year limited warranty in the marketplace
- Comes complete, just open the box, remove and install
|
 |
Powerhouse 1HP Ice Eater
Part # P1000-25-115V
- 1 HP energy efficient high quality motor
- 115 volt, 7.0 amps, one phase, 60/50 cycle
- 25 foot quick change power cord
- Two 25 foot x 3/8" hollow braided mooring lines with shackles
- Dimensions of shipping box, 14 1/2 x 14 1/2 x 16 1/8"
- Shipping weight 45 lbs
- For large boats, marinas and heavier uses
- Can be used in place of several smaller units
- Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water; Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified
- Motor shaft is 316 stainless steel, the best material for salt water application
- Permanent split capacitor ensures quick high torque and smooth operation, while producing the highest efficiency of a single phase induction motor; Motor and capacitor are matched for ultimate performance
- Internal, heavy duty, hard faced mechanical seal with stainless components immersed in dielectric lubricating fluid Additional double lip shaft seal for extra protection
- Stator motor windings have double impregnation of baked insulating varnish
- Two heavy duty ball bearings provide support for the rotor while being cooled with dielectric type oil
- Sacrificial custom designed zinc is provided for conditions where electrolysis may be present
- Propeller is custom designed for maximum thrust and performance Propeller screws on shaft for easy removal and replacement
- Twenty-five feet of 16/3 water and oil resistant cord with three prong molded plug is standard; Additional length cord available: 50 and 100 feet
- Heavy duty PVC custom brackets that attach motor to shroud; All stainless bolts and locking aircraft nuts are used
- Performance certified tested at our facility for proper output and leaks before shipment
- Best three year limited warranty in the marketplace
- Comes complete, just open the box, remove and install
|
 |
Powerhouse 1HP Ice Eater 230V
Part # P1000-25-230V
- 1 HP energy efficient high quality motor
- 230 volt, 3.5 amps, one phase, 60/50 cycle
- 25 foot quick change power cord
- Two 25 foot x 3/8" hollow braided mooring lines with shackles
- Dimensions of shipping box, 14 1/2 x 14 1/2 x 16 1/8"
- Shipping weight 45 lbs
- For large boats, marinas and heavier uses
- Can be used in place of several smaller units
- Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water; Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified
- Motor shaft is 316 stainless steel, the best material for salt water application
- Permanent split capacitor ensures quick high torque and smooth operation, while producing the highest efficiency of a single phase induction motor; Motor and capacitor are matched for ultimate performance
- Internal, heavy duty, hard faced mechanical seal with stainless components immersed in dielectric lubricating fluid Additional double lip shaft seal for extra protection
- Stator motor windings have double impregnation of baked insulating varnish
- Two heavy duty ball bearings provide support for the rotor while being cooled with dielectric type oil
- Sacrificial custom designed zinc is provided for conditions where electrolysis may be present
- Propeller is custom designed for maximum thrust and performance Propeller screws on shaft for easy removal and replacement
- Twenty-five feet of 16/3 water and oil resistant cord with three prong molded plug is standard; Additional length cord available: 50 and 100 feet
- Heavy duty PVC custom brackets that attach motor to shroud; All stainless bolts and locking aircraft nuts are used
- Performance certified tested at our facility for proper output and leaks before shipment
- Best three year limited warranty in the marketplace
- Comes complete, just open the box, remove and install
- Optional thermostat custom design turns Ice Eater on when needed; Ideal for unattended application
|
 |
Powerhouse 3/4HP Ice Eater (100' Power Cord)
Part # P750-100-115V
- 3/4 H.P. energy efficient high quality motor with 36 pounds thrust
- 4.7 amps, 115 volt, one phase, 60/50 cycle
- 100' power cord
- Two 25 foot x 3/8 hollow braided mooring lines with shackles
- Dimensions of shipping box 14 1/2 x 14 1/2 x 16 1/8
- Weight 45 pounds
- Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water; Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified
- Motor shaft is 316 stainless steel, the best material for salt water application
- Permanent split capacitor ensures quick high torque and smooth operation, while producing the highest efficiency of a single phase induction motor; Motor and capacitor are matched for ultimate performance
- Internal, heavy duty, hard faced mechanical seal with stainless components immersed in dielectric lubricating fluid; Additional double lip shaft seal for extra protection
- Stator motor windings have double impregnation of baked insulating varnish
- Two heavy duty ball bearings provide support for the rotor while being cooled with dielectric type oil
- Sacrificial custom designed zinc is provided for conditions where electrolysis may be present
- Propeller is custom designed for maximum thrust and performance; Propeller screws on shaft for easy removal and replacement
- Twenty-five feet of 16/3 water and oil resistant cord with three prong molded plug is standard; Additional length cord available: 50 and 100 feet
- Heavy duty PVC custom brackets that attach motor to shroud; All stainless bolts and locking aircraft nuts are used
- Performance certified tested at our facility for proper output and leaks before shipment
- Best three-year limited warranty in the marketplace
- Comes complete, just open the box, remove and install
- Optional thermostat custom design turns Ice Eater on when needed. Ideal for unattended application
|
 |
Powerhouse 1/4HP Ice Eater - 115V with 25' Cord
Part # P250-25-115V
HP: 1/4
Amps* 115V: 2.5
Open Diameter**: 20-25 ft.
Cord Length: 25 ft.
All units available in 230V, (halve the amps, i.e., 2.5 @ 115V = 1.25 @ 230V).
** 200 Ft. available in 230V only
*** Based on an average winter - extreme conditions will cause open diameter to become smaller.
When water freezes, it expands, becoming lighter. This fact is the principle upon which Ice Eater functions. Ice Eater circulates warmer bottom water to the top, thereby preventing ice formation. If surface ice already exists, the flow of warmer bottom water will effectively melt it. Ice Eater obtains its superior operating efficiency through the use of an axial flow, shrouded propeller design. This design also privdes protection for the rotating propellor.
|
 |
PowerHouse Ice Eater 1 HP 115V w/100' Cord
Part # P1000-100-115V
Model P1000
Ice Eater P1000 - 1 HP propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation. Ice Eater will melt existing ice. 3-year limited warranty!
Ice Eater P1000, unlike other de-icing units, requires no additional hardware in order to obtain the desired de-icing pattern. Ice Eater is shipped complete with suspension lines. It can be taken out of the box, hung in place and plugged in. Ice Eater may be hung from a pier or boat. Two to three feet is the average operating depth.
Ice Eater P1000 Features:
- Standard 100' quick change power cord.
- Two 25 ft. x 3/8 in. hollow braided lines with shackles
- Environmentally friendly lubricant
- Patented Venturi Design for maximum thrust
- Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water. Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified. Motor shaft is 316 stainless steel, the best material for salt water application. Optional thermostat custom design turns Ice Eater on when needed. Ideal for unattended application.
Specifications:
- Horsepower: 1 HP
- Power needed: 115V, 7.0amps, 1-phase, 50Hz
- Typical Thrust: 42 lbs. thrust
- De-Ices Diameter of: Approx. 80 ft.
- Uses: De-icing large boats, marinas, or to replace several smaller units
|
 |
PowerHouse Ice Eater 1HP 230V w/100'Cord
Part # P1000-100-230V
Model P1000
Ice Eater P1000 - 1 HP propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation. Ice Eater will melt existing ice. 3-year limited warranty!
Ice Eater P1000, unlike other de-icing units, requires no additional hardware in order to obtain the desired de-icing pattern. Ice Eater is shipped complete with suspension lines. It can be taken out of the box, hung in place and plugged in. Ice Eater may be hung from a pier or boat. Two to three feet is the average operating depth.
Ice Eater P1000 Features:
- Standard 100' quick change power cord.
- Two 25 ft. x 3/8 in. hollow braided lines with shackles
- Environmentally friendly lubricant
- Patented Venturi Design for maximum thrust
- Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water. Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified. Motor shaft is 316 stainless steel, the best material for salt water application. Optional thermostat custom design turns Ice Eater on when needed. Ideal for unattended application.
Specifications:
- Horsepower: 1 HP
- Power needed: 230V, 3.5 amps, 1-phase, 60Hz
- Typical Thrust: 42 lbs. thrust
- De-Ices Diameter of: Approx. 80 ft.
- Uses: De-icing large boats, marinas, or to replace several smaller units
|
 |
ICE EATER 1 HP 115V 25FT CORD - The Power House
Part # P1000
Designed to prevent ice formation around boats marinas floating docks piers pilings boat houses bulkheads and fish and duck ponds. The propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation. Will melt existing ice. Just cut a hole and lower the unit into place.
|
 |
1/2 HP 115V 25FTCORD ICE EATER - The Power House
Part # P500
Designed to prevent ice formation around boats marinas floating docks piers pilings boat houses bulkheads and fish and duck ponds. The propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation. Will melt existing ice. Just cut a hole and lower the unit into place.
|
 |
Powerhouse 150' Replacement Power Cord
Part # 12150
150' Replacement Power cord for Ice Eater Units
|
 |
Powerhouse 200' Replacement Power Cord f/230V Units Only
Part # 12200
200' Replacement Power Cord for 230V Ice Eater Units Only
|
 |
Powerhouse 220V Thermostat w/Adjustable Temp Range
Part # KP16220
ICE EATER THERMOSTAT - 220V
Adjustable Thermostat. Temperature range from 30°F to 110°F For use in both salt water and fresh water.
|
 |
Powerhouse 3/4HP Ice Eater 230V w/100' Cord
Part # P750-100-230V
Ice Eater P750 - 3/4 HP
Propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation. Ice Eater will melt existing ice. 3-year limited warranty!
Features:
Ice Eater P750, unlike other de-icing units, requires no additional hardware in order to obtain the desired de-icing pattern. Ice Eater is shipped complete with suspension lines. It can be taken out of the box, hung in place and plugged in. Ice Eater may be hung from a pier or boat. Two to three feet is the average operating depth.
Ice Eater P750 Features
3/4 HP energy-efficient high quality motor with 36lbs thrust
230V, 2.35 amps, 1-phase, 50/60 Hz
Two 25' x ු hollow braided lines with shackles
Environmentally friendly lubricant
Patented Venturi Design for maximum thrust
Weight: 45lbs
Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water. Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified. Motor shaft is 316 stainless steel, the best material for salt water application. Optional thermostat custom design turns Ice Eater on when needed. Ideal for unattended application.
Specifications:
- Horsepower: 3/4 HP
- Power needed: 230V, 2.5 amps, 1-phase, 50/60 Hz
- Typical Thrust: 36lbs thrust
- De-Ices Diameter of: Approx. 60'
- Uses: De-icing mid-sized boats and docks
|
 |
Powerhouse 3/4HP Ice Eater 115V w/50' Cord
Part # P750-50-115V
Ice Eater P750 - 3/4 HP
Propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation. Ice Eater will melt existing ice. 3-year limited warranty!
Features:
Ice Eater P750, unlike other de-icing units, requires no additional hardware in order to obtain the desired de-icing pattern. Ice Eater is shipped complete with suspension lines. It can be taken out of the box, hung in place and plugged in. Ice Eater may be hung from a pier or boat. Two to three feet is the average operating depth.
Ice Eater P750 Features
3/4 HP energy-efficient high quality motor with 36lbs thrust
115V, 4.7amps, 1-phase, 50/60 Hz
Two 25' x ⅜ hollow braided lines with shackles
Environmentally friendly lubricant
Patented Venturi Design for maximum thrust
Weight: 45lbs
Motor housing is constructed of 16 gauge 304 stainless steel and bronze endbell for corrosion free operation in fresh or salt water. Motor exceeds NEMA specifications and is UL and CSA compliant, and C.E. certified. Motor shaft is 316 stainless steel, the best material for salt water application. Optional thermostat custom design turns Ice Eater on when needed. Ideal for unattended application.
Specifications:
- Horsepower: 3/4 HP
- Power needed: 115V, 4.7amps, 1-phase, 50/60 Hz
- Typical Thrust: 36lbs thrust
- De-Ices Diameter of: Approx. 60'
- Uses: De-icing mid-sized boats and docks
|
No Review for Powerhouse 1/2HP Ice Eater
No Review for Powerhouse 3/4HP Ice Eater
No Review for Powerhouse 1HP Ice Eater
No Review for Powerhouse 1HP Ice Eater 230V
No Review for Powerhouse 3/4HP Ice Eater (100' Power Cord)
No Review for Powerhouse 1/4HP Ice Eater - 115V with 25' Cord
No Review for PowerHouse Ice Eater 1 HP 115V w/100' Cord
No Review for PowerHouse Ice Eater 1HP 230V w/100'Cord
No Review for ICE EATER 1 HP 115V 25FT CORD - The Power House
No Review for 1/2 HP 115V 25FTCORD ICE EATER - The Power House
No Review for Powerhouse 150' Replacement Power Cord
No Review for Powerhouse 200' Replacement Power Cord f/230V Units Only
No Review for Powerhouse 220V Thermostat w/Adjustable Temp Range
No Review for Powerhouse 3/4HP Ice Eater 230V w/100' Cord
No Review for Powerhouse 3/4HP Ice Eater 115V w/50' Cord
This product ships in 1 business day.
To determine the shipping cost and estimated delivery date for this item click Add to Cart, then click Calculate Shipping inside your shopping cart.
Standard Shipping Policies
Please be careful when ordering this product, it has limitations that differ from our General 30-day Return Policy. After all, we want you to be satisfied with your order so you'll return again and again as an iboats.com customer, and to also recommend us to your boating friends
- Electronics/Software/Videos
- Electronics/Software/Videos are not returnable. Please be careful when ordering to choose the correct product.
See our complete return policy.
|
