Rule Pumps non-automatic bilge pumps offer traditional operation activated by a float or panel switch. Removal of the motor cartridge allows for easy cleaning of the strainer and impeller in the event that the pump becomes clogged with debris. Electric Submersible Pumps are by far the most popular type of electric Bilge Pumps, submersibles give very high outputs, are cost effective, have low amp draw and are easy to install. They are designed to fit in the lowest part of the bilge and only require discharge pipe work and electricity supply. However, flow rates decrease more rapidly than other types of pumps as the discharge head increases, so check our recommended maximum discharge heads and if in doubt, always increase the size of the pump. Although our submersibles can be run dry for up to 2 hours, pump life can be extended by avoiding dry running whenever possible. All submersibles can be operated using a float switch, and remotely controlled by using a switch panel.
 |
Rule Manual Bilge Pump 360 GPH 3/4" Port 12v
Part # 24
- The Rule 360,non-automatic offers many design features while keeping size and cost to a minimum.
- Especially popular on smaller craft.
- Rule 360 pumps are unmatched in pumping power and longevity.
- 3/4" discharge outlet.
- 12 DC volt.
|
 |
Rule Manual Bilge Pump 500 GPH 3/4" Port 12v
Part # 25D
- The Rule 500 non-automatic offers many design features while keeping size and cost to a minimum.
- Especially popular on smaller craft.
- Rule 500 pumps are unmatched in pumping power and longevity.
- 3/4" discharge outlet.
- 12 volt.
|
 |
Rule Bilge Pump 800 GPH Manual 12v 3/4" Port
Part # 20R
This pump offers the highest capacity pumping performance of any pump with a 3/4" discharge hose. This pump allows a performance upgrade from Rule 360's and 500's without the hassle of changing strainer baskets. discharge hoses, or thru-hull fittings. Features: AMP draw @ 12.0V DC: 2.8 Dim.: 3-3/4" H x 2-3/8" W
|
 |
Rule Manual Bilge Pump 1100 GPH 1-1/8" Port 12v
Part # 27D
- The Rule 1100 non-automatic pump offers impressive pumping power for its size and cost.
- Competitive models in this pumping range are much larger and far more expensive.
- 1-1/8" discharge outlet.
- 12 volt.
|
 |
Rule Manual Bilge Pump 1500 GPH 1-1/8" Port 12v
Part # 02
High pumping capacity and reliability at a lower cost. Pumps 1500 G.P.H. The Rule 1500 pump continues to offer more pumping capacity and more exclusive design features than any comparable competitive pump. 1-1/8" outlet.
|
 |
Rule Manual Pump for Bilge 2000 GPH 1-1/8" Port 12v
Part # 10
Engineered to commercial standards, the Rule 2000 is the best selling high capacity submersible bilge pump in the world.
- Non-automatic: Activated by a float or panel switch
- Capacity GPH: 2000
- Panel Switches: 41,43,45,49
- Float Switches: 35,37,40
- Volts: 12DC
- Amps @12v: 8.4
- Amps @13.6v: 12.0
- Fuse Size: 15
- Height (inches/mm): 6 (152)
- Width (inches/mm): 4-1/4 (108)
- Weight (lbs/kg): 2/15 (1.3)
- Hose Diameter (inches/mm): 1-1/8 (28.6)
Rule's Cartridge Series of Bilge Pumps offers traditional operation activated by a float or panel switch. These are non-automatic pumps with the added option of replacement motors. This feature allows you to carry a spare motor, providing an extra level of security and protection. Removal of the motor cartridge also allows for easy cleaning of the strainer and impeller area in the event that the pump becomes clogged with debris. Replacement motors are sold separately.
|
 |
Rule Bilge Pump Manual 3800 GPH 12v 15 Amp 1 1/2" Port
Part # 17A
The Rule General Purpose Pump is designed for use as a washdown pump and/or to circulate water to your livewell tank(s). Heavy duty construction for use on commercial or pleasure boats. 1-1/2" (38mm) inlet and 1-1/2" (38mm) discharge outlet. The Rule General Purpose Pump must be mounted below the waterline. It does not deliver high pressure, nor is it self priming. It delivers lots of water but at low pressure. 12 volts DC.
Specifications
- Flow Rate 3800 gph
- Port Type 1 1/2" (38mm) Hose barb
- Voltage 12 Vdc
- Designed for use as a wash-down pump and/or to circulate water to your livewell tank(s)
- Heavy duty construction for use on commercial or pleasure boats
- Must be mounted below the water line
- It does not deliver high pressure, nor is it self priming
- It delivers alot of water but at low pressure
- 3800 G.P.H. capacity
- 8-1/2"W x 5-1/4"H.
- Inlet 1-1/2"
- Discharge outlet 1 1/2"
- 12 volt
|
 |
BILGE PUMP 12V 2000 GPH UL APR
Part # 106UL
Designed for the toughest applications. Designed to produce the highest capacity available for a pump its size. 2" discharge outlet. 106UL pump is UL Listed and includes 6' leads. Gold series pumps feature a 5-year warranty.
|
 |
Marine Bilge Pump, 4000 GPH, 12V
Part # 56D
- Designed for tougher applications.
- Compact, efficient and maintenance free.
- Totally submersible, ignition protected.
- Anti-airlock feature.
- Exclusive moisture tight seals.
- Positive snap lock strainer base.
- Silent running and vibrationless.
- Water cooled motor and no burn-out when run dry.
- Stainless steel shaft.
- Hose Stud Size: 2".
|
This product ships in 1 business day.
To determine the shipping cost and estimated delivery date for this item click Add to Cart, then click Calculate Shipping inside your shopping cart.
Standard Shipping Policies
Based On 2 Reviews
