Taylor Made
Hot Shot T-Top Boat Cover (Fits 19'5" to 20'4" Length, 102" Width w/o Bow Rails, Single Engine Cut-Out)
Price: $407.98
Save: $402.85
(49% Off $810.83)
Part # 497665

The three main features of these covers are:

    1. Bow and stern sections are separated into two halves.The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. The stitching of the zippers into the cover halves feature beginning each zipper at the top of the console tube and ending at the hem (finished outside edge). This allows installation of the cover by a single person inside the boat.
    2. The "console tube" or center portion of the cover fits over the console and under the T-top.Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of the console tube incorporates an adjustable draw rope in both front and rear sections. The draw ropes tighten the tube from side to side around the T-top verticals and also are used to secure the tube to the upper horizontal supports of the T-top. The "console tube" is not a perfect rectangle as it comes up off the cover halves. Rather it is more trapezoidal in shape and wider at the base than at the top. This feature allows these covers to fit and function properly even though there are variations in size and position of the T-tops within the confines of the hull and deck.
    3. Tie down system in the hem or perimeter of the covers.To relieve stress on the zippered ends during over the road trailering Taylor Made has added a webbing strap and quick release buckle to the cover at both sides just above the zipper to facilitate the installation of the cover by a single person. The rope that spans the perimeter of the cover is made into two sections. The first goes from one side at the zipper opening, around the bow to the same point on the opposite side. The second goes around the stern of the boat in a similar fashion.
Hot Shot T-Top Boat Cover (Fits 19'5" to 20'4" Length, 102" Width w/o Bow Rails, Single Engine Cut-Out)

The three main features of these covers are:

    1. Bow and stern sections are separated into two halves.The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. The stitching of the zippers into the cover halves feature beginning each zipper at the top of the console tube and ending at the hem (finished outside edge). This allows installation of the cover by a single person inside the boat.
    2. The "console tube" or center portion of the cover fits over the console and under the T-top.Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of the console tube incorporates an adjustable draw rope in both front and rear sections. The draw ropes tighten the tube from side to side around the T-top verticals and also are used to secure the tube to the upper horizontal supports of the T-top. The "console tube" is not a perfect rectangle as it comes up off the cover halves. Rather it is more trapezoidal in shape and wider at the base than at the top. This feature allows these covers to fit and function properly even though there are variations in size and position of the T-tops within the confines of the hull and deck.
    3. Tie down system in the hem or perimeter of the covers.To relieve stress on the zippered ends during over the road trailering Taylor Made has added a webbing strap and quick release buckle to the cover at both sides just above the zipper to facilitate the installation of the cover by a single person. The rope that spans the perimeter of the cover is made into two sections. The first goes from one side at the zipper opening, around the bow to the same point on the opposite side. The second goes around the stern of the boat in a similar fashion.
Full StarFull StarFull StarFull StarEmpty Star
Semi-custom boat cover for ~20' center console boat with T-top and no bow rails
by Jerry from Tallahassee, Florida on November 06, 2017
My requirements were for a modestly priced (~$300), reasonably durable boat cover which would protect my single outboard Key West 203FS with T-top from the bulk of leaves and other debris, and shield from the sun the boat's permanently affixed upholstery. Specifically, I wanted a cover which did NOT fit over the T-top, but was secured immediately beneath the T-top cover. This product meets those needs, and is consistent the description provided in the offering. The fabric is of good quality, not outstanding the sewing, seaming, cinch points, etc., are of solid but not exceptional design. To reiterate, this is a semi-custom, modest price point product, and it very well satisfies those criteria. As a semi-custom cover, it does not fit the boat like a glove, but does fit generally securely. Near the underside of the T-top, where the top of the cover itself is secured, there is quite a bit of 'bagginess' and excess material again, a function of a generic boat cover design. It was easy enough to ad-lib some of the strap placements, and add a couple of nylon rope additions, to make the cover secure. Otherwise, it fits quite well. Of positive note, there is a full zipper amidships on both sides of the cover, so accessing the boat with the cover on is easy - open either port or starboard zipper. As well, if more convenient, the boat cover can be separated into two pieces - forward and stern - if desired. Other similar boat covers have zippers, but many cannot be fully separated because the skirt line is continuous, whereas on this one the skirt line and cinch cord are separated forward and aft amidships at the same point as the zippers. All in all, I am very satisfied with this product. The only reason I don't give it five stars is because the material and construction, while quite good, are not excellent. But again, this is a $300 semi-custom cover, not an $800 custom product. So, I highly recommend it if your needs are generally the same as mine.
Was this review helpful?
Q:
I have a 1997 Regal Destiny 200, center console deckboat with a T-Top. Will this cover fit my boat?
A:
This is a semi custom cover and is designed to fit the T-Top Style of boat. You'll need to measure your boat to make sure that the lengths, widths, and all other specifications match up. Make sure to read the "Description Tab" on the product as well, as it goes into more detail.


Ask a question
Question & Answer Guidelines
5 year limited warranty
7 colors available
6.25 oz. per square yard
Acrylic coated polyester
Fair
Excellent
Excellent
Fair
Good
Good
This product ships in 9 business days.
Add to Cart and enter your Postal Code to determine the shipping charges.
Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies

Please be careful when ordering this product, it has limitations that differ from our General 30-day Return Policy. After all, we want you to be satisfied with your order so you'll return again and again as an iboats.com customer, and to also recommend us to your boating friends

Semi-Custom Boat Covers

Semi-custom covers are "made-to-order" and are thus specific to your order. However, we understand that sometimes a product you purchase just doesn't work out, which is why we want to make the return process as easy as possible for you. After all, we want you to be satisfied with your order so you'll return again and again as an iboats.com customer, and to also recommend us to your boating friends.

A made-to-order semi-custom cover may be returned within the first 30 days after shipment, but is subject to a 15-25% restocking fee. Odd-Lots, Liquidations, In-Stock Specials, Closeouts and customer requested alterations are non-returnable unless an error was made by iboats.com or by the boat cover manufacturer.

Merchandise must be in new, unused condition with all original packaging in good condition; plus parts, accessories, manuals, and/or warranty cards included. You will need to receive a return authorization number (RA #) as well as instructions from our Customer Service Department.

Please note that each boat cover manufacturer may have additional requirements concerning product returns or warranty claims, including but not limited to: restocking fees, shipping fees, or product order change fees.

Because boat covers are "made-to-order", there will be a $25-$50 fee for any boat cover order cancellation after 1 business day of purchase, as the cover has already gone into production.

Warranty Policy

30 days after the purchase date, the manufacturer of the product(s) will need to be contacted for a warranty claim.

Returns for Canadian Customers

Canadian customers, please be careful when placing your order; iboats.com does not accept any return merchandise on Canadian orders unless the merchandise you received was defective, damaged, or an error was made by iboats.com. In such cases, please contact iboats.com Customer Service within 30 days of the original shipping date for a return authorization number. Returned items that do not have a RA # will not be accepted.

See our complete return policy.