Unepoxy Standard Antifouling Paint - Pettit Paint
- 45% Copper
- Excellent Performance at an Economical Price
A high performance economy antifouling paint which has been custom formulated to provide outstanding bottom protection at a very affordable price. Unepoxy Standard is a modified epoxy that dries to a hard finish able to withstand season-long use and abuse. It has excellent adhesion to fiberglass, wood and properly primed steel hulls and is compatible over most previously applied bottom paints. Use Thinner 120.
All paint colors shown here are for guidance only. Due to differences in screen displays that are beyond our control the colors on these pages cannot be guaranteed to match the actual color in the can.
Unepoxy is a hard protective antifouling paint for use on boat bottoms. It can be applied over most aged hard antifouling coatings. Old soft antifouing paints should be removed for best adhesion. It may be applied on fiberglass boats with outboards or outdrives with no danger of electrolysis, provided that drive units are not coated themselves. Unepoxy is also suitable for all non-aluminum trailered boats that are used for durations of up to two weeks in salt or fresh water before retrailering.
Unepoxy has excellent adhesion to fiberglass, wood and steel hulls and is perfect for both power and sail boats. Its compatibility with all properly prepared hard bottom paints permits safe overcoating without fear of lifting.
Disclaimer: Charts apply to Pettit products only. The information provided is not intended to be exhaustive. Because iboats.com does not know how this information is being used, they cannot take responsibility for any actions as a result.
The performance of marine paint depends on many factors outside the control of iboats.com, including surface preparation, proper application, and environmental conditions. Therefore, iboats.com cannot guarantee this product's suitability for your particular purpose or application.
By purchase or use of this product, buyer agrees that the sole and exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at iboats.com's option.
Pettit Paints - Unepoxy Standard Antifouling
|Product Type||Hard Antifouling|
|Key Attributes|| •Contains the highest copper load in its class |
•Durable hard finish is able to withstand season-long use
•Dependable antifouling at an affordable price
•Excellent coverage, adhesion, and compatibility
|Technology & Formulation||Solvent Based, Modified Epoxy|
|Substrates||Fiberglass, Wood, Steel, Lead, Bronze. (For more specific instructions per substrate, please refer to the product data sheet provided below.)|
|Thinner||Pettit 120 Brushing Thinner|
|Mixing Instructions||Thoroughly mix - can be thinned up to 10% to ease application|
|Method||Brush, Roller, Airless or Conventional Spray|
|Application Temperature||40°F - 90°F|
|Number of Coats||2-3|
|Recoating Information (Recoat/Relaunch)|| DRY TIME (HOURS): To Recoat / To Launch|
90°F: 2 / 8
70°F : 3 / 16
50°F: 6 / 24
|Repaint Information||Pressure wash upon haulout, heavily sand, clean and reapply. (Refer to the Pettit Antifouling Compatibility Chart found below for more information.)|
Associated Products From Pettit Paint:
- Pettit Protect 4700/4701
- Brushing Thinner 120
- Spray Thinner 121
- Bio Blue 92
- Fiberglass Dewaxer 95
- Tie Coat 6627
Unepoxy Product Data Sheet PDF
Pettit Antifouling Compatibility Chart
MSDS for Unepoxy Blue*
MSDS for Unepoxy Green*
MSDS for Unepoxy Red*
MSDS for Unepoxy Black*
*Disclaimer:Information on this material is subject to change without notice. Please visit the corresponding manufacturer's website for updates.