Zinc Coat Boat Barnacle Barrier 1792 - Pettit (Kop Coat) - Pettit Paint

Zinc Coat Boat Barnacle Barrier 1792 - Pettit (Kop Coat) - Pettit Paint
Your Price: $21.65
Save: $14.14
(39% Off $35.79)
Part # 1792 ValueShip™ Eligible
SHIPS TODAY!* if ordered in 5 hrs 14 mins.
Pettit Paint

Product Families

Pettit Zinc Coat Barnacle Barrier Underwater Metal Paint
    The Pettit Zinc Coat Barnacle Barrier Underwater Metal Paint offers a simple and highly effective solution to protect all the underwater metal parts …
    Features:
    • Fast dry.
    • Superior adhesion to clean metals.
    • 93% pure zinc in the dried film.
    • Supplied in an easy to use aerosol spray can.

    Spray can designed for protecting transducers.

    General Description:
    This product is for use only on bare metals such as steel, stainless steel, cast iron, copper, bronze, galvanized steel and lead. It forms an excellent adhesive bond to underwater metals and running gear and inhibits corrosion on these surfaces. Because of its smooth, hard surface it will self-clean in service. Zinc Coat can be used above or below the waterline. Do not apply anti-fouling paint over Zinc Coat. For metal above the waterline apply one (1) coat of Pettit 6627 Tie-Coat Primer after the Zinc Coat has dried for 2 hours. Follow with two (2) coats of Pettit Easypoxy Enamel. The dried film of Zinc Coat contains 93% pure zinc.

    Application Information
    Shake can vigorously for one minute after mixing balls begin to rattle. Shake often during use. Hold can upright 12 to 16 inches from the surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface and in motion while spraying. Applying in thin coats. Allow no more than 5 minutes between two or three thin coats, otherwise allow to dry one hour before applying additional coats.

    When finished spraying, clear spray valve by turning can upside down and spraying until no more paint comes out. If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits. Do not stick a pin or other object in the stem.

    Surface Preparation
    Remove all paint from underwater metals and runing gear by sanding, scraping, sandblasting or by using a paint and varnish remover. Once back to bare, clean metal wipe the surface with Pettit 120 Brushing Thinner and let dry.

    For application to metals above the waterline remove all paint and rust with a wire brush or sandpaper. Lightly sand glossy surfaces. Clean surface with Pettit 120 Brushing Thinner and let dry.

    NOT FOR USE ON FIBERGLASS OR WOOD

    Disclaimer: Charts apply to Interlux products only. The information provided is not intended to be exhaustive. Because iboats.com does not know how this information is being used, they cannot take responsibility for any actions as a result.

    The performance of marine paint depends on many factors outside the control of iboats.com, including surface preparation, proper application, and environmental conditions. Therefore, iboats.com cannot guarantee this product's suitability for your particular purpose or application.

    By purchase or use of this product, buyer agrees that the sole and exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at iboats.com's option.

    ok
    by Jose from Elgin, Illinois on May 09, 2014
    Thanks
    Was this review helpful?
    Zinc Coat Boat Barnacle Barrier 1792 - Pettit (Kop Coat) - Pettit Paint
    by Robert from Saraland, Alabama on April 03, 2014
    It has not been enough time to give you a good review, send this back in about 2 Months.
    Was this review helpful?
    zinc coat
    by Stephen from Holbrook, Massachusetts on May 30, 2013
    works good
    Was this review helpful?
    Zinc coat boat barnacle barrier
    by Robert from Essex, Maryland on February 15, 2013
    I like the product very much ,but I haven't used it at this time because its to cold. I will use it in the spring before I launch my boat Bob Arvey
    Was this review helpful?
    Product arrived quickly and packed well
    by David from Warwick, Rhode Island on April 12, 2012
    I was impressed with the speed of delivery and the fact that the product was well packed. The Zinc Coat Barnacle Buster was easy to apply and was as described. I will not know until the end of the summer, if it works as stated but that is a Pettit issue. IBoats was the best buy for this product, including shipping charges. I will use Iboats again .
    (2 of 6 people found this review helpful)
    Was this review helpful?
    Barnacle Barrier
    by David from Purcellville, Virginia on March 06, 2012
    Easy to use although a bit runny if you are not careful. Works as advertised seems to last the season (Chesapeake Bay).
    (1 of 1 people found this review helpful)
    Was this review helpful?
    Ask a question for
    Question & Answer Guidelines
    This product ships in 1 business day.

    Add to Cart and enter your Postal Code to determine the shipping charges and estimated delivery date.
    * Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
    Standard Shipping Policies