Evinrude E70TLCRD owner.
Have paid for servicing in the past, but am going to do the 'easy' stuff for now on.
I'm about to change the gearcase oil, spark plugs and perform an engine tune up. I have everything that I need to perform these services.
My question:
Should I apply Permatex Anti...
Evinrude 1984 E70TLCRD motor:
The water intake screen is completely broken; basically it's like it's not even there.
I found the part number to be: 0320042
Unfortunately, the part is obsolete; or atleast I've had an impossible time trying to find it.
My question:
Can I use a correct...
I'm gonna install a KeelGuard on my 1985 14' McKee.
The McKee is a tri hull boat.
I know that I will definitely install a guard on the center keel.
But I was wondering if I should install a guard on the outter keels as well.
Basically, should I put KeelGuards on all three of the tri hull's...
I was in the process of adding anodes to my E70TLC (evinrude 1984 70hp) and the filler block bolt broke off at the head. Basically, I cannot remove the filler block because of the busted bolt. I was able to add the 'u-shaped' anode (forward aft anode?). My question is: The busted bolt...
First, I tested my tachometer and it received power but no signal. So I had local shop replace my bad rectifier and tested stator which is good.
Upon testing after repairs the tachometer still receives power and no signal. So obviously there is corrosion in the remote control area where the...
First, I tested my tachometer and it received power but no signal. So I had local shop replace my bad rectifier and tested stator which is good.
Upon testing after repairs the tachometer still receives power and no signal. So obviously there is corrosion in the remote control area where the...
Recently purchased a new Faria 7000 RPM Tachometer to replace the old busted/broken original tachometer.
I performed a preinstall to test the set up; plugged wire harness into new tach and cranked engine before fully installing into console. The tach registered power (needle moved from resting...
I am going to soundproof or at least decrease the noise that escapes from my motor.
I plan on buying Acoustiblok (4'x5' panel) and cut to shape for the inside of my cowling.
Does anyone have a good high temperature adhesive recommendation?
I've found 3M Hi Strength 90 Aerosol Adhesive, but am...
In the process of adding some gauges to my Evinrude E70TLCRD (70HP, 1984).
Setting up new Faria Tachometer (preping system before a final install) and the needle on the Tach registers (moves from rest to 0 RPM) but Tach does not register with engine on. So it receives power but no signal...
I have ordered a Faria Water Pressure Gauge for my Evinrude E70TLCRD (70HP, 1984).
I wish to keep the Tell-Tale by using a Connector-Tee at the Water-Jacket; sending tubing to gauge and tell-tale nipple.
My question is:
Can I use Connector-Tee - 0123553
I found it under the water...
I have ordered a Faria water pressure gauge (30psi) and a Faria cylinder head temperature gauge (60-220F) for my Evinrude E70TLCRD (70hp, 1984).
The install for both are pretty self explanatory.
Water Pressure Gauge:
The instructions say: "On your engine, locate and remove the plug that is...
My first post:
So I bought a new Faria Tachometer and tested it and found that it receives power but no signal; so, I jumped the gun and ordered a new rectifier for my Evinrude E70TLCRD (1984). I'm assuming that the rectifier is bad and not sending the signal. I will install rectifier upon...
