Search results

  1. S

    1985 Evinrude 30 tilt/shallow drive mechanism

    This is also a 85 (co). If this picture doesn't get what you want ask me what specific area to take a picture of.
  2. S

    1988 Evinrude 90 VRO alarm at startup

    Definitely not normal, If I can remember right there's two alarms on your control box. One, which I think is constant, is an overheat and one that's intermittent, that's for low oil or low oil pressure. You need to determine which one it is. Definitely want to make sure you're getting oil. An...
  3. S

    Need help!

    Did any water come out of the gearcase when you drained the oil? It still looks like 2 stroke oil to me. Has it been run in a barrel for awhile?
  4. S

    Need help!

    No.....excess 2 stroke oil. Get her on the lake and clean her out.
  5. S

    1975 Johnson 25 HP Not Running

    Running an inline fuel filter? Sounds fuel related. I'd pull that carb, clean it again and run on a portable fuel tank until you resolve the issue.
  6. S

    1975 Johnson 25 HP Not Running

    Two different fuel tanks?
  7. S

    i command gauges

    I had one but never experienced that. Use this link to go where everyone goes when you have an etec issue. Report back later with any findings. Good luck https://www.etecownersgroup.com/etec-v4-136484
  8. S

    Kill switch question

    Not spring loaded.....lots of parts but doable.
  9. S

    Ready to call 911

    Congratulations..... Always feels good once it all works out.
  10. S

    Ready to call 911

    This video is a little better in my humble opinion....shows how to make the brush holder while you assemble. Saves the cost of buying one plus the other guy didn't explain or aline it properly. Cheers
  11. S

    Ready to call 911

    You use this button to post a picture. After pushing it, it takes you to pictures on your phone....scroll through them until you find the pic you want and then post it.
  12. S

    1976 6 hp Evinrude "slipping or over reving" coming up on throttle.

    More of a cap than a nut but whatever.
  13. S

    1976 6 hp Evinrude "slipping or over reving" coming up on throttle.

    I'm not aware of any "prop nut".... should be a shear pin and a cotter pin. I'm betting internal gear assembly issue or two old fat guys in an overloaded 14 ft boat shooting birds might have to do something with it! 😜 Might be time for a bigger motor.
  14. S

    1975 Johnson 25 HP Not Running

    Yes, so it's probably time to tell him how to lap the new flywheel and mount it correctly so it doesn't happen again to him.
  15. S

    1975 Johnson 25 HP Not Running

    Not sure anyone needs to answer that, common sense says "yes" Finding the problem often is much harder than fixing it so I think you shall be rewarded soon.
  16. S

    1975 Johnson 25 HP Not Running

    Post pictures of cracks....began to start but didn't have enough to start....enough what? Backfiring is typically timing so your on to something. Make sure your plug wires are on the right plug.
  17. S

    1975 Johnson 25 HP Not Running

    I assume you tried screwing it out more correct?
  18. S

    1975 Johnson 25 HP Not Running

    I see.....I re-read the thread and it said you cleaned the carb, try rebuilding the carb. You might not have cleared everything as well.
  19. S

    1975 Johnson 25 HP Not Running

    By the way Race, please explain how does one put in one half of a drop?!😆
  20. S

    1975 Johnson 25 HP Not Running

    You need to diagnose the fuel pump before diving into all of this. Put drips in the cylinder but use a small spray bottle of fuel (50 to 1 fuel) to keep it running (throat of the carb) and then start pumping the ball and see if it runs. It's either fuel pump, carb related (not cleaning it...
View older results
Top