Search results

  1. C

    96 johnson 150

    I pulled each plug wire, one at a time, cylinders #1,4,5, and 6 are dead. its barley running on #2 and #3.. When i check the spark on the dead cylinders, the plugs are firing to ground, with a spark about 3/4 inch and blue in color.
  2. C

    96 johnson 150

    i have pulled the plug wires off, its running on 2 cylinders, #3 an #2 the other 4 don't change with them on or off. but all 6 wires are firing good.
  3. C

    96 johnson 150

    its running on cylinders 2,3,4
  4. C

    96 johnson 150

  5. C

    96 johnson 150

    runn Running in a Barrell. strong spark about an inch. week spark on the back side of the plug, real week, I must have the wrong plugs ,nkg bpr7hs. the manual says that it could be fuel leak through the primer solenoid. that make scene, the electric primer stopped working, it may be stuck, I...
  6. C

    96 johnson 150

    I pull the plug wires one at a time while running, it sparks from inside the cup to 3/4 to an inch out to a head bolt, but when I pull a plug and with wire connected to the plug, the spark is week, barely jumps to ground at a 1/16 or less. the plugs seem to be the problem ngk bpr7hs 6422
  7. C

    96 johnson 150

    compression is 100 +- 5 psi, I heard the were low compression motors, I just put new plugs in, I think is being flooded with fuel, or the power pack is week, the idle screws on half the carbs has no effect on it. I started pulling plug wires, its running on 3 cylinders. I have a spark tester...
  8. C

    96 johnson 150

    problem: rough idle \ runner good at wot 21 ft. CC running 32 mph that's what it was before rebuild Things I've done. 1. tested the coils 2. test resistance on plug wires 3. tested resistance on plugs 4. tested plugs for blue spark. 5. set the timing @ 6 btc per manual. 6. removed 6 carbs and...
  9. C

    Mariner. 93, 75 hp.

    I'm replacing all seal and gasket in my lower unit, I'm waiting on parts to arrive, I have removed the outer seal from the exhaust housing ( not sure if that the proper name for it,) I have removed the outer seal with my seal removal tool, it was tight due to oxidation, my question is how to...
  10. C

    Water pump issues

    Thanks
  11. C

    Water pump issues

    One more thing, on the old water pump, I put a hose on the pump to flush it backwards, water was leaking from the drive shaft. I'm thinking, if the impeller is pressed in tight, how would water get past the impeller? This test was low pressure water
  12. C

    Water pump issues

    I'm working on a 1993 manier 75 hp Boats been sitting for a long time, I get it started, water pump not working, removed lower unit, flushed the motor from the bottom with a hose, a little dirt washed our, than ran clear. Replaced complete water pump housing, impeller gaskets. The kit came...
  13. C

    Electrical pronlems.

    I'm thinking of everything. The emergency disconnect on the control was wasn't stopping it from starting before. Can I by pass it for now too see if it's killing all the power?
  14. C

    Electrical pronlems.

    This generic diagram shows a fuse at the motor, the only one I've seen was a old glass bulb type, I cut it out and installed a new blade type. There is power at this fuse.
  15. C

    Electrical pronlems.

    93 manier 75 hp Working on a boat for a friend, drops it off, not running, and has been sitting for a few years, replaced bad stater (copper wire on brushes came lose) got it started, replaced water pump, linkage was jacked, someone connected the throttle on the wrong side, idle position was...
  16. C

    93 manier 75 hp

    Is the plastic part like a cover to hold cables in place?
  17. C

    93 manier 75 hp

    It's remote controls
  18. C

    93 manier 75 hp

    I'm looking for a part or part name, for the plastic piece that holds the shifting cables in place on the side of the motor, it held on with 2 push pins. I don't have a model number, And it's not shown on the parts diagram from retailers. Like Crowley's
  19. C

    96 johnson. Link and sink

    96 j150exedb The trunion nut is maxed out. I leaned a new word. Lol
  20. C

    96 johnson. Link and sink

    96 johnson exeedb 96 johnson 150 exedb
Top