Search results

  1. C

    96 johnson. Link and sink

    The cable is not long enough to hold the roller against the timmer plate. I rebuilt the motor, same cables from old motor. The only thing that could have happen, i used linkage parts from 95, mines an 96, I would have never thought they were not the same motor
  2. C

    96 johnson. Link and sink

  3. C

    96 johnson. Link and sink

    I have set my like and sink, with the cam roller touching the timmer base, it starts and idles, when i connect the cable, it pulls the roller off the timer base 1/4 or so. In this position, will not idle, I had bought a new control box during my build, Should this motor idle the the rolled of...
  4. C

    96 johnson timing.

    I had the boat idling on a hose at 900 rpm. I took it to the lake and it will not idle. Useing a timming light, i can not get the idle timming below 10 degrees btdc. It should be 4-6 atdc No matter what i do, i canr get it firing atdc. At wot it hits 20 degree as it should. It will barely idle...
  5. C

    96 johnson timing.

    Only for v4 using #2 plug
  6. C

    96 johnson timing.

    The manual gives 2 options for timing,) if you can see the photo) I have rebuilt the motor and it starts and idles fine. I'm putting it in the water tomorow to set low and high timing. With the motor warm, should it be set at 4-6 btdc? or 4-6 atdc for normal operation? If i understand...
  7. C

    Cooling problems

    Ok., i have my new water punp. Looking at the service manul, it shows the order to installing the pump Reading the pump installment instruction are different. Here are 2 pic. Pump supplier call for number 10 and 11 Manual call number 10 only.
  8. C

    Cooling problems

    I put the thermostats in water on the stove, they both opened about 145. I just replaced the cup and impeller. I did notice the cap didn't seem flat, I was having problems with the new house and rubber gasket staying in place. so, I used the old one. I'm ordering a new pump and will uses all of it.
  9. C

    Cooling problems

    Up date. I tested the t states at 145 +- they are good. Idle 1000 rpm post is running 120 to 130 Starboat side 150 +- At 800 rmp they both rise but starboard side close to 170. Then i shut it down. This on the hose. I dont think the tell tale is not puting out as much water as it had last...
  10. C

    Cooling problems

    I have the manual. I beleive you have answered my question. My test was without the t stats. I was thinking one was bad so i removed it. I will test them today and see it they open at the right temp before i install them. Thanks For your reply.
  11. C

    Cooling problems

    I rebuilt it this winter. It starts and runs?. It runs good. Was taking it to the the lake to set wot timming. When the water was flowing good, i had concerns the port side ran cooler. But starboard side was warmer. Its pumping water, but its not getting to the power head. It leaking somewhere...
  12. C

    Cooling problems

    I pulled the the lower unit put, removed everything. I was missing the garment inside the wp hose housing. I put it back on the muffs. Removed the thermostates and the plugs for them. Its peeing 1/4 the water it should be, the same as the last pump. I have water coming up and pouring down...
  13. C

    Cooling problems

    The last last one ran about 10 minutes, i said 20 but it was closer to 10 if that matters when runnig dry. Ot did not show any signs of damage, did not has any rubbing scars, ss plate and cap look good. But i went a head and install the new. Im fixing to pull it and if i missed somthing. How...
  14. C

    Cooling problems

    I bought an after marked control box. I could find the wire by color and add one.
  15. C

    Cooling problems

    The last one is brand new, i only ran it long enough to see if it was gong to pump water. It was not ran but about 15 to 20 seconds, so it didn'd burn up.
  16. C

    Cooling problems

    Yes, book said to seal the top and bottom of the gaskt for the wear plater. O ring gets 4 drops, one a each corner to avoid blocking the primer hole. Oring under impeller and key in the slot. Its the same extion i had before. I can fell the water tube be pushing into the pump. I have pulled...
  17. C

    Cooling problems

    1. It ran 2 minutes max without water. 2. I dont think it has an over heat alarm. Its plug in the harness but i dont now where it would located. 3. Motor is rebuilded with less than an hour run time. Motor starts right up and idles good. i havent test compressi because motor run good.
  18. C

    Cooling problems

    This a total rebuild on 96 Johnson j150exedb. I finally got the motor running 800 rpm and water pump building up good pressure, but with the hose Muffs. this was my second water do to my mistake. Wednesday, I had finally got the boat ready to take to the lake to set the timing at wot. Thursday...
  19. C

    How to disable quick start on 96 Johnson 150

    I need to set my timing with quick start disconnected. Why does the manual show the motor firing @ 6 degrees after TDC, and 19 to 20 degrees btdc (it's always before TDC for automobiles.) Mine is idling warm at 6 degrees btdc @ 800 rpm
  20. C

    96 Johnson 150 Setting idle

    I have, just have not recieved it yet, for now im using Selco. I cant find the wide open throttle timing in this book. It referes to using an analyzer. Im using a timing light. Joe says it should 4 degrees less than the manufactors setting. But i cant fint the settings.
Top