Search results

  1. C

    Seastar hydrolic steering testing

    I'm having problems after I hit the motor putting extreme pressure on. I lost my steering. Things done i have bleedit to death many times. I have removed it an totally disassembled it twice, every thing was oily and spotless clean, removed the 4 springs and ball bearing twice. Secondtime I...
  2. C

    Teleflex sterring

    I'm needing a new sterring cable for sh5023 helmet sterring box. My old cable is ss07217. I can't find a replacement for it. Are these cables replaceable? Or do i need to replace everything?
  3. C

    Over revving

    1987 j 48 rebuild cards, fresh gas. It's starting on manual hockey, ideal rough. Sometimes it starts revving like thet when they are running out of fuel. The settles down to rough idea. After 20 minutes of messing With it. It has started revving out of control on its on, I had6to chock it...
  4. C

    Seastar hydraulic

    I have damaged part number 5 on my pump HH5271 build-in lock valve for positive rubber lock. Seastar doesn't sell this part. Does anyone know where I can buy one? Thanks.
  5. C

    Steering setup

    I'm looking to replace the steering system on a 87 johnson 48 hp. Most I look at are Chinese and universal. Will they work on my boat? Where is a good place to one of good quality?
  6. C

    97 mercury 115 hp. Drive shaft removl

    I can't get the drive shaft out the lower unit. Pinion gear nut is off, the crankshaft seal housing is off. In the pictures there something that looks like the back of a seal ive tried to drill a small hole, so I can pull it with a puller. I don't have a manual. This is a one time seal job for...
  7. C

    Johnson PTT colors

    I'm connecting a 96 150 Ignition wire harness a 1990 150. The 90 has 4 wires for TT BLUE, GREEN, RED, AND BROWN. the 96 has BLUE ,GREEN AND A WHITE I only have a manual for the 96. I would think the red would connect with the white with tan stripe for power. What is the brown on the PTT plug...
  8. C

    Lawrence FS 9

    I had a Lawrence elite ti2 I was had problems, it was about 3 years old, I sent it in under a 50% warranty, 220. To fix or 460. To replace it. With a 6 month warranty. They sent me a Lawrence elite fs 9, The problem is the typographical maps Is not very detailed, it's missing a 2 mile...
  9. C

    Acceleration problems

    1996 j150 My boat starts with the flip of the key. She will idle in gear, it's struggles and dies when I accelerate, if I push it slowly. It will run rough but I can to WOT and runs great, then I can back of to 1/4 throttle and still runs great. But if I go back to idle, it's struggles on...
  10. C

    Pulling a boat motor.

    I'm fixing to pull a 90 johnson 150 from a boat to my stand, is it safe to lift the motor using 3. 5/15 bolts in the flywheel? If the is a better way other than buying a i-boat for the crankshaft. If i know the thread type, I could buy a not and build one,
  11. C

    I have a Lawrence 9 ti2, blank white screen.

    I have a 3 year Lawrence ti2. I've only used a fer times, i had a boat rebuild take long than it should have, First problem was a grounding issue, tech support walk my through it. I c an hold the power wire to get a good ground, Not sure if its fixed, Went out the last 2 times, and touch...
  12. C

    AC voltage 1990 evenrude

    I bought a 1990 evenrude 150. I got the motor running, Im checking everything out, Running, I get 9.0 volts ac on ( y1, ) and 2.4 volts ac on( y2 ) Together I get 25 volts ac I have 3 Stater plates to compare against each other for resistance, One on a running motor, one is extra parts and...
  13. C

    Power head swap

    I have a 1996 Johnson 150 , I purchased a 1991 Evinrude xp 150 that runs great. the linkage is the same, I know ill need a cord adapter, my question is, will this power head bolt to my mid section? are the driveshaft splines the same?
  14. C

    96 johnson 150

    problem: rough idle \ runner good at wot 21 ft. CC running 32 mph that's what it was before rebuild Things I've done. 1. tested the coils 2. test resistance on plug wires 3. tested resistance on plugs 4. tested plugs for blue spark. 5. set the timing @ 6 btc per manual. 6. removed 6 carbs and...
  15. C

    Mariner. 93, 75 hp.

    I'm replacing all seal and gasket in my lower unit, I'm waiting on parts to arrive, I have removed the outer seal from the exhaust housing ( not sure if that the proper name for it,) I have removed the outer seal with my seal removal tool, it was tight due to oxidation, my question is how to...
  16. C

    Water pump issues

    I'm working on a 1993 manier 75 hp Boats been sitting for a long time, I get it started, water pump not working, removed lower unit, flushed the motor from the bottom with a hose, a little dirt washed our, than ran clear. Replaced complete water pump housing, impeller gaskets. The kit came...
  17. C

    Electrical pronlems.

    93 manier 75 hp Working on a boat for a friend, drops it off, not running, and has been sitting for a few years, replaced bad stater (copper wire on brushes came lose) got it started, replaced water pump, linkage was jacked, someone connected the throttle on the wrong side, idle position was...
  18. C

    93 manier 75 hp

    I'm looking for a part or part name, for the plastic piece that holds the shifting cables in place on the side of the motor, it held on with 2 push pins. I don't have a model number, And it's not shown on the parts diagram from retailers. Like Crowley's
  19. C

    96 johnson. Link and sink

    I have set my like and sink, with the cam roller touching the timmer base, it starts and idles, when i connect the cable, it pulls the roller off the timer base 1/4 or so. In this position, will not idle, I had bought a new control box during my build, Should this motor idle the the rolled of...
  20. C

    96 johnson timing.

    The manual gives 2 options for timing,) if you can see the photo) I have rebuilt the motor and it starts and idles fine. I'm putting it in the water tomorow to set low and high timing. With the motor warm, should it be set at 4-6 btdc? or 4-6 atdc for normal operation? If i understand...
Top