Search results

  1. brim_buster

    Gaskets

    If I wanted to make a new fuel pump gasket for the 59 Wizard or any other fuel related rubber gasket, does anyone have a recommendation for what and where to purchase such material?
  2. brim_buster

    80 Evin 25 wont shut off

    In an earlier thread I had issue with no spark. Got that problem fixed with charge coil. Now the engine fires right up, mind you I have the kill switch black and yellow wire disconnected, and when I turn the key off the engine still runs. Brand new key switch that was working fine. Any ideas...
  3. brim_buster

    5 old outboards to restore

    A gentleman sold me his dads old outboads. A 60's Gale Buccaneer 25hp in really nice shape all complete. A 59 Wizard 7.5 hp in nice shape. A Scott Atwater 1-12 early 50's 3.6hp needs alot of work but is complete. The gas tank is completely rusted on the inside. A Ted Williams 4.5hp in nice...
  4. brim_buster

    1980 Evin 25 lost spark

    was running then I lost spark on both plugs. Wheres a good place to start trouble shooting? Has CDI ignition.
  5. brim_buster

    1980 Evinrude 25hp armature plate.

    Is it possible to convert my now armature plate with the current set-up over to a set-up with points and condensors?
  6. brim_buster

    1980 25hp Evin planes out then dies

    So for the last 2 weeks after rebuilding the carb thinking that was the problem and buying a new gas tank, this motor will plane out and then die flat on its face. It wont fire right back up and if it does all I can do is putt around. If I go to give it gas it will die. Then its a bear to get...
  7. brim_buster

    80 Evin 25hp key ignition

    Was out on the boat and the key ignition was working fine as it has been. Then I went to start it and nothing. Made sure it was in neutral. Wiggled the ignition and still nothing. Go back to the motor which has a button for starting and it fired right up. My logic is the key ignition was shot...
  8. brim_buster

    80 Evinrude 25hp model e25rcsa

    Can I use ear muffs on my motor. Ive bee using a barrel?
  9. brim_buster

    1980 Evin 25hp now dies

    Was running good last week then now it shuts down after running for about 5 minutes. Was trying to upload a video but its too big
  10. brim_buster

    82 Evin 35 low idle knob adjustment

    I just got the foot back on with new foot oil and got the new impellor in and working. Now I trying to fine tune it for the river. Carbs been apart and cleaned and now I want to adjust the low idle knob and was wondering if there were any tips anyone had. My manual only goes to 78 with a 33hp...
  11. brim_buster

    82 Evin 35 hp foot removal

    Im trying to remove the foot to install oil and impellor. Disconnected the shift rod retaining clip thats located in the water inlet on the foot per you tube video and the nut on the threaded bolt on top the foot and the 4 bolts holding the foot on and this thing wont budge.Im thinking the shaft...
  12. brim_buster

    Wico coil swap

    Went to this site http://oddjobmotors.com/tt1_replacewico_coil.htm and followed the instructions and made 2 good coils out of some shot out Wico coils. It took about 30 minutes to do both and worked flawlessly. The hardest part was getting the spark plug wires situated. I had 2 coils from my 53...
  13. brim_buster

    53 Firestone 5hp

    just picked up a 1953 Scott Atwater Firestone Serial #17353877 Code 133-3-1735 model 10 A 73 . Anything I should know before I start the overhaul/ restore on this purdy thing?
  14. brim_buster

    1952 evinrude 3 hp

    My manual goes back to 65 and says 50:1 fuel mix and SAE 90 foot oil for these. Im restoring one and does any one know if thats correct by chance? Thanks guys
  15. brim_buster

    The new format of this site

    WOW never had so many problems now that they tried to fix something that worked fine before. Wish they would go back to the old format for this forum:facepalm:
  16. brim_buster

    1996 Mariner 9.9 4 stroke question

    Just purchased this motor for my stick steer and was wondering how I flush the motor? Not that it will ever see salt water but I would of thought it would use earmuffs but now Im thinking I have to use my water barrel:facepalm: This is my first 4 stroke motor and it was just serviced, took it...
  17. brim_buster

    62 Elgin 7.5 hp

    Ok the wifes gonna kill me but I just purchased a 1962 Elgin in really nice shape. Other than they are hard to work on from what Ive read, any advice or pointers anyone can share. oil/gas ratio etc. never owned one but looks like it was a good find.:D
  18. brim_buster

    7.5 hp 4 stroke carb issue

    BF75-1101072 just did a trade and got this gem. Got it to run and she sounds sweet BUT.... at the top of the carb where the vents are its leaking gas. Went through the carb and got it cleaned and when I fired it up I noticed there was a screw in one side run all the way down and gas coming out...
  19. brim_buster

    1949 QD 10 Sea horse

    Just bought a nice, clean 49 QD 10. Was wondering 2 things, do I have to use a pressurized gas tank? The other thing is can you still get parts like carb kit and water pump etc. Any help would be great. Thanx in advance for you help.:joyous:
  20. brim_buster

    My 89 Gamefisher 9.9 update.

    After reading numerous post concerning the same issues I have with my Force, heres an update. stuck a needle in the vent on carb to make sure it was clear. took carb apart to make sure the needle was seating, which it is. brand new carb from **********. everything was good internally in carb...
Top