Search results

  1. nola mike

    5.0 Mercruiser Problems

    It needs 12v to keep it closed/off. Unplugging it will make it rich I believe. Whether it can be removed completely I'm not sure. Should be able to just swap in a standard carb though.
  2. nola mike

    New lower shift cable

    Did you skip the parts about checking the system for slop? Does it shift normally using the cable?
  3. nola mike

    1997 Merc 4.3 V6 LXGen+

    First time I've seen a coil replacement as a fix for a loose distributer...
  4. nola mike

    Lower unit and or motor & lower unit swap

    No, pressure test the drive, find out where the leak is Everything can be done with enough time and money. If they offered a 4.3 you might get lucky and have mounts there. I had to fab mine. You'll need a bit more width with a v6
  5. nola mike

    Lower unit and or motor & lower unit swap

    Yeah, but all that means it's that you have a leak somewhere. It will probably be easier to fix what's wrong than to swap parts around. The 4.3 will be a definite upgrade, but might/probably won't be plug n play in your boat.
  6. nola mike

    Lower unit and or motor & lower unit swap

    Some fuzz is normal, chunks of metal are not. There is no "usual" bad seal (why do you think you have a bad seal?), but prop seal is not one of the usual suspects...
  7. nola mike

    Starting issue

    I did something like this with a steering cable. Worked for a bit, but failed within a season or so. For the amount of work involved, might as well replace the cable if available
  8. nola mike

    Has anyone self-changed the trim sensors on a 3.0 XL Alpha One drive?

    I think it's worse on a gen 1. Ted, if you had a smaller boat you could just turn around and see if you're kicking up a wake...
  9. nola mike

    '09 5.0 TKS (Carb) not running

    Can't think of why he'd lose spark after 5 minutes of running though, unless the temp switch closing did something. Op, do you have 12v at the coil pos when you lose spark?
  10. nola mike

    Rochester 2 jet running rich before and after rebuild

    https://quadrajetparts.com/power-piston-rochester-7006011-7009718-p-498.html
  11. nola mike

    A1G2 decisions. Rebuild or replace?

    I thought we were talking about the u-joints being bad?
  12. nola mike

    '09 5.0 TKS (Carb) not running

    Ok... 1. Engine cranks. So Yellow/red to slave and then to starter is good. 2. Gauges presumably work with ignition on, so purple circuit is good. 3. Nothing off of the starter lug when cranking, so that's an issue. However, I'd verify it with the P/Y disconnected at the starter. 4. When you...
  13. nola mike

    1984 Rinker

    You're in the wrong forum, but by far the biggest worry in an '84 is structural. Stringers/transom. Any engine problems are comparatively easy to fix. However, 2 stroke mercs are not known for their reliability
  14. nola mike

    Starting issue

    1. Troubleshooting is free 2. Why would you change out a working part?
  15. nola mike

    Breather hose

    I don't have the part number off hand, but there's nothing magic about it. Get the diameter, go to the auto parts store and get a length of whatever.
  16. nola mike

    1997 Merc 4.3 V6 LXGen+

    I use a regular box wrench and expletives
  17. nola mike

    Bravo 3 Oil Leak - Oh No !!!

    Makes sense, but never thought about it in the case of twins.
  18. nola mike

    Starting issue

    You'd be better off actually troubleshooting the problem rather than throwing parts at it and wasting your time and money...
  19. nola mike

    Bravo 3 Oil Leak - Oh No !!!

    When reading about your port/std markings, was wondering if the b3 twins counter rotate, or if the 2 props make that unnecessary
  20. nola mike

    1989 5.7 350 Mercruiser ignition replacement help - possible upgrade to DUI unit

    Ah. "Ignition module". Or apparently official name is "ignition amplifier"
Top