Search results

  1. nola mike

    Can the base of engine work? Two to bolts under engine are rusted and can

    Oh right. Still seems like a good way to have a leak at the transom seal to leave that bolt out, even if you glob sillycone into the hole.
  2. nola mike

    Can the base of engine work? Two to bolts under engine are rusted and can

    Can that bolt even be accessed with the engine in? I'm thinking it's on the transom plate beneath the y pipe? And also supports the transom plate...
  3. nola mike

    Mercruiser 3.0 TKI engine crank half time - never starts

    Sounds like an issue with your batteries or connections. Connections especially given your breakdown. Engine doesn't require much power once running. Don't see a pic posted. Neither I nor Google knows what a boat gard is.
  4. nola mike

    Mercruiser 4.3 Ignition Troubleshoot Process

    However, I'd start at the kill switch. It supplies your ignition power. Check the purple wire on both sides of the switch.
  5. nola mike

    Mercruiser 3.0 No Spark issues

    This is a slow motion train wreck. Please drill the transom.
  6. nola mike

    2002 Four Winns 248 Vista with Volvo Penta 5.0 GXI

    I'll buy it today for $13k.
  7. nola mike

    Water in bilge has returned in 1995 Four Winns 190 Horizon

    Relying on a bilge pump to keep up with a leak of unknown origin is not a smart or safe way to boat. Absolutely terrible advice.
  8. nola mike

    Need Assistance to Diagnose Bravo 3 - 5.0L MPI Vibration

    However you did it, it sure looks like it's aligned now. Only thing I might try is to rotate the engine and make sure that the alignment stays in check throughout its rotation. The coupler splines are aluminum versus the harder steel splines, so much more likely to do coupler damage (I've never...
  9. nola mike

    Need Assistance to Diagnose Bravo 3 - 5.0L MPI Vibration

    Are you saying that you needed the pry bar to get the alignment tool in? Or was that just initially when setting up?
  10. nola mike

    Can the base of engine work? Two to bolts under engine are rusted and can

    Wonder if that bolt broke/corroded off. Remember that much of the beginning of this thread were half assed attempts to work around rot... Losing that bolt would go with a rotten transom.
  11. nola mike

    Bellow replacement job

    After mine failed the last time I didn't try to fix. Never even bothered to hook them back up when I did the engine swap, and disconnected the gauge when I was chasing gremlins a few weeks back. My to do list is always too long to even bypass the limit switch 😄
  12. nola mike

    Sticky Throttle cable? Shift Cable? Help!

    Usually if the cable is bad, it activates the switch inappropriately. And then a lazy owner will disconnect the switch rather than replace the cable.
  13. nola mike

    Sticky Throttle cable? Shift Cable? Help!

    Check to see if your shift interrupter switch is working. It's supposed to momentarily kill power to the engine when you're coming out of gear. Without that working, it will be hard to get out of gear. It's a small switch centered in a v-shaped plate near the shifter cables. Push the switch, it...
  14. nola mike

    Mercruiser 3.0 No Spark issues

    Bigger bit is easier to see what you got, maybe ¼". Try plugging the exhaust and idle relief ports and then filling the pipe. Dunno if something simple like a bag and rubber band over the prop and stuff something in the ports would do it. It wouldn't need to be perfect, just enough that you're...
  15. nola mike

    Mercury MCM165 6CYL 250CID Exhaust Riser for Holley Sniper

    The snipers are coming down in price to where they're getting competitive with a brand new carb. Especially for a custom build, I think having a/f data is invaluable. Having spent a lot of time at it, you can tune a carb on a boat "good enough", but without a way to get objective data you're...
  16. nola mike

    Mercruiser 3.0 No Spark issues

    I'd drill the transom to find out for sure. It takes 10 minutes. Also don't know if your garden hose test is valid, as unless the exhaust is plugged you aren't completely filling the y pipe. In the water that's completely full.
  17. nola mike

    Had spindal changed now water coming in back of boat

    They would have had to remove the damper and belts... Literally no reason at all to do that. Also, there's no such animal as a spindal. Maybe some pics might help.
  18. nola mike

    1990 3.0 mercruiser ignition voltage issues

    Not too strange. In the start position the normal ignition circuit is bypassed. No...The issue is upstream of the problem. The power draw with the ignition on could be from the gauges, choke, or ignition system with the ignition on. But those are supposed to draw power. Not sure which wires...
  19. nola mike

    Boat will not plain fast

    How many RPMs do you get once it planes out at WOT?
  20. nola mike

    Can the base of engine work? Two to bolts under engine are rusted and can

    That's a backfire.
Top