Search results

  1. nola mike

    Longshot help for friend, '98 EFI fuel check valve?

    Yes... I would have advised against this boat for a number of reasons. Do you have a parts diagram showing the valve, or is it integral to the pump?
  2. nola mike

    Longshot help for friend, '98 EFI fuel check valve?

    Long shot here, but I have an...over excited... friend who bought a '98 Regal with a "new" engine that ran in the driveway. It is apparently missing a "fuel pressure check valve" because the guy that replaced the engine forgot to put it in and is an "easy fix". The boat is not nearby so I can't...
  3. nola mike

    Help Diagnosing carb vs ignition problem, 5.7 mercruiser

    Lol.
  4. nola mike

    Help Diagnosing carb vs ignition problem, 5.7 mercruiser

    Based on what? He hasn't checked spark when it dies.
  5. nola mike

    Wiring help/Electronic gauge

    Had high hopes for this. After hooking up and then trying to figure out why the engine wouldn't start (gee, maybe it's that new electrical connection, dumbass), it looks like the gauge somehow grounds out this wire. Wish I had a DSO to figure out what's going on, but was getting about 2.5v off...
  6. nola mike

    Help Diagnosing carb vs ignition problem, 5.7 mercruiser

    How about you confirm that it's an ignition problem? When it doesn't start throw a timing light on a lead or use a spark plug tester and see.
  7. nola mike

    Wiring help/Electronic gauge

    TL;DR Could I splice the gauge input into the grn/wht wire from my TB IV module? @achris ? Long version: OK, so I contacted the gauge seller, who told me that the gauge won't accept a coil neg input. He said it would take the input from a regular magnetic 2 wire sensor, which he offered to send...
  8. nola mike

    87’ invader mercruiser help me ! 👸

    I'll disagree with you on this one. I still haven't noticed a *huge* increase in power, although the v6 is much smoother and the power is effortless mid-range, I'm not usually looking to accelerate quickly from 25-40 knots. I want it down low, and I think the 200# weight penalty of the v6 hurts...
  9. nola mike

    87’ invader mercruiser help me ! 👸

    Ok. You won't gain much in power with the swap. In fact, depending on how that v6 is set up you might lose power. Also it sounds like a) you'd be in over your head and b) you don't have anyone who knows wtf they're doing. You would need a *complete* v6 with all the accessories. You would need to...
  10. nola mike

    87’ invader mercruiser help me ! 👸

    What's wrong with the current motor? I would *highly* recommend against this swap. It is not easy and takes a decent amount of know how to accomplish. Whatever is wrong with your current setup, it would almost certainly be a better idea to fix what you have. Besides, you have a pretty rare beast...
  11. nola mike

    Boat won’t plain starts too then just spins like slipping clutch

    Or stripped outdrive gears, broken driveshaft in the drive, or spun coupler. Which aren't cheap.
  12. nola mike

    Wiring help/Electronic gauge

    Anybody have any thoughts?
  13. nola mike

    No spark plug spark... 170 MC , 1985 Sea Ray

    Again, the cranking 12v to the coil on your engine comes from the pur/yell wire off the slave solenoid.
  14. nola mike

    Ignition switch failing?

    Huh, you mean like this? Was tracking down a voltage drop this weekend. Still got 0.25v across the switch, but this cost me almost 1v with no load
  15. nola mike

    Dripping engine block fitting

    It's just a standard npt pipe fitting, but I don't remember the size. ¼?
  16. nola mike

    1994 5.7L Weber carb

    Yup, I jumped to fuel without reading closely and noticing the misfire
  17. nola mike

    New to forum

    The space between is dry. Also that lower seal goes in the opposite way you'd expect, lip faces up. It should stop a leak from that upper seal if the drive shaft is installed.
  18. nola mike

    Cracked block - now looking to replace motor

    Your outdrive will work. Are all the accessories coming with the new motor?
  19. nola mike

    Dripping engine block fitting

    It'll drain a couple of gallons. Of course we have no idea what engine you have... Also, what's the rest of that rust from?
  20. nola mike

    Motor Knock

    Yeah, I'd be concerned about the crank, maybe bearings if it dropped that hard. I'd at least demand an extended engine warranty for a year or 2
Top