Pettit Paint Zinc Prop Coat Barnacle Barrier 1792, 16 oz. 1792
Available:Out of stock
Part:Mfg 1792, iboats IB00084296, UPC 725469019157
- Fast dry.
- Superior adhesion to clean metals.
- 93% pure zinc in the dried film.
- Supplied in an easy to use aerosol spray can.
Spray can designed for protecting transducers.
This product is for use only on bare metals such as steel, stainless steel, cast iron, copper, bronze, galvanized steel and lead. It forms an excellent adhesive bond to underwater metals and running gear and inhibits corrosion on these surfaces. Because of its smooth, hard surface it will self-clean in service. Zinc Coat can be used above or below the waterline. Do not apply anti-fouling paint over Zinc Coat. For metal above the waterline apply one (1) coat of Pettit 6627 Tie-Coat Primer after the Zinc Coat has dried for 2 hours. Follow with two (2) coats of Pettit Easypoxy Enamel. The dried film of Zinc Coat contains 93% pure zinc.
Shake can vigorously for one minute after mixing balls begin to rattle. Shake often during use. Hold can upright 12 to 16 inches from the surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface and in motion while spraying. Applying in thin coats. Allow no more than 5 minutes between two or three thin coats, otherwise allow to dry one hour before applying additional coats.
When finished spraying, clear spray valve by turning can upside down and spraying until no more paint comes out. If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits. Do not stick a pin or other object in the stem.
Remove all paint from underwater metals and runing gear by sanding, scraping, sandblasting or by using a paint and varnish remover. Once back to bare, clean metal wipe the surface with Pettit 120 Brushing Thinner and let dry.
For application to metals above the waterline remove all paint and rust with a wire brush or sandpaper. Lightly sand glossy surfaces. Clean surface with Pettit 120 Brushing Thinner and let dry.
NOT FOR USE ON FIBERGLASS OR WOOD
Disclaimer: Charts apply to Interlux products only. The information provided is not intended to be exhaustive. Because iboats.com does not know how this information is being used, they cannot take responsibility for any actions as a result.
The performance of marine paint depends on many factors outside the control of iboats.com, including surface preparation, proper application, and environmental conditions. Therefore, iboats.com cannot guarantee this product's suitability for your particular purpose or application.
By purchase or use of this product, buyer agrees that the sole and exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at iboats.com's option.
- Brand Pettit Paint
- Manufacturer Sku 1792
- UPC 725469019157
- Days to ship from warehouse - 1
- Length 2.8333
- Width 3.5355
- Antifouling Type Specialty
- Color Grey
- Compatibility Metal
- Size Aerosol
General Return Policy
An item(s) may be returned within the first 30 days after the item(s) is shipped to you. Merchandise must be in new, unused condition with all original packaging in good condition; plus parts, accessories, manuals, and/or warranty cards included. You will need to receive a return authorization number (RA #) as well as instructions from our Customer Service Department.
Please start your return online to receive your RA #. Returned item(s) that do not have a RA # will not be accepted.
* Please note: iboats.com does not accept any return merchandise on Canadian & International orders. See our Canada & International Return Policy
After 30 days of your purchase, the manufacture of the product(s) will need to be contacted for a warranty claim. If you need assistance finding the manufacturers number please contact our Customer Service Department.
Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.