Hello To All,
I thought I would share some info that just may help someone out there..
I own a 98 merc 150 outboard V-6, S# 0G740674.
Long story short..
I had an issue that I knew was fuel related,
I rebuilt the carbs a few times, Rebuilt fuel pumps, Changed fuel filters, Fuel water...
Hello All,,
This is the problem I am having.. The boat Idles Fine and tops out fine and runs at 45 Mph...
If I throttle up fast the boat will take off, If I throttle up slow she starts to bogs at 1800rpms every time and if I don't ease off or throttle through it she will DIE!!!
I have switch...
Hello All,
I have a 98 merc carberated that runs real strong..
The problem that I am having is that if say im trolling and RPMs are at 2000, the motor after a bit will run up to 2500 RPMS on its own with out me bumping up the throttle.. It does not seem to happen all the time but alot.. What...
Well Hello Again all,
I have finally finished my project and I am now back fishing, Have not realy caught to much but I am back in the ocean.. Boat has been finished for a little while now..
Sorry been gone so long and have not updated post, Here are some pics.. I will get some more current...
Hello all,
Well my 98 merc 150 Model 1150422UD, Serial 0G740674, has been running awesome, And is actually still running awesome, ..
My last trip out the overheat alarm starting going off, but boat was not over heating..
I have the alarm and I also have another temp gauge, The gauge reads...
Hello All,
I am having a small problem I thought maybe some of you guys maybe able to help me out here...
I have a 98 Merc 150 , I am having problems with the tilt trim.. The motor will go down but not up, So I switched the relays then the motor goes up and not down... This would mean to me...
Hello All,
Just picked up a honda 8 hp 4 stroke, Not sure on year.. Model is bF8A..
Started motor up and notice water pouring out from the top of the engine, right where it meets the block,
Is this the head gasket? Or maybe a cracked head..
Thanks
Ant...
Re: 1976 Aquasport 19.6. cCC..Outboard Engine mounting bracket questions.. Plz help
Here is a picture of the dusky bracket I will be using, Not going to boat today afterall, But will be back at boat saturday... I believe model # is 0599, Hard to see it and tell what it is..
Thanks again
Hello All,
I have just finished , Well almost finished a complete restore on a 19'.6" / 1976 Aquasport / cc..It had an open transom which I enclosed and am going to add an engine bracket..
I am little confused as where to exactly place the bracket on the transom... ( Don't want to screw this...
Hello All,
I am in need of little help here..
I just completly restored a 1976, 19.6 Aquasport center console, I did stringers, enclosed the Transom, and the deck...
I have an outboard mercury 150, With a 25" shaft.... I purchased an outboard engine bracket that will bolt on the back of the...
Hello All,
I am working on a boat right now which is a 1991 Sunbird with a 115HP Johnson outboard ( Quit Rider set up)..
There seems to be a problem with the tilt/trim sender unit location.. There is one on there but it is not or cant be in the right location as the contact leaves the lever...
Hello All,
I have a 91 , 115HP Johnson that I am working on.
Heres whats happening...
When I raise the motor as far up as it will go, the trim gauge needle is in the up position, When I lower the motor back down the gauge will not go below the half way line on the gauge...
What shuld I...
Re: MY NEW PROJECT.. 1976 AquaSport 19.6 Could Use A little advise
Hello Again guys,
Well I have cut out the bad sections and it was not that bad at all.. The rotted wood Has been removed from the deck..
Looks like the fuel tank was changed at one time and who ever did it did not do a very...
