Recent content by archery1

  1. archery1

    1990 johnson gt 150

    I recently bought a hydra sports vs150ff that has a johnson gt150 on it. Motor runs great with plenty of power. I have owned 2 other boats and they both had force motors on them so i used the tc3 oil . Was wondering what oil would be good to use with this johnson motor...
  2. archery1

    Getting it ready to take out on water

    Bought a 1990 hyrdasports with a johnson gt150 on it,
  3. archery1

    Evinrude 3hp Duck Twin - Year?

    I have one of these with serial # 3032-01744 how do i find the year?
  4. archery1

    Wanting to get a new prop

    I have a 1990's 90hp force outboard. The late Frank had put my motor on my boat. It has a aluminum prop on it and it is getting rough looking. I have looked on prop and the only number i see on it is 15. I have been looking at aluminum, stainless or even these composite props .I have no idea...
  5. archery1

    Help with wiring a auto/ manual rocker pump and aerator timer panel

    My friend has a tracker boat (older) he is retired and has a limited income. His wires melted from his timer an pump switch . I need a wiring diagram for it. thanks for any help you can give. just trying to help a fisherman out His auto/ manual rocker to fill livewell works but the timer...
  6. archery1

    Question about oil

    I have a 1990 90hp force outboard . I am going to need oil to mix in gas for it really soon. I had quicksilver and another type (in blue jug) in the past and they were both non synthetic oils. Question is is it OK to start using semi or full synthetic oil to mix in gas 50:1 ratio ? Thnx
  7. archery1

    installing a tach

    My boat has not had a working tach since the other motor was put on. A good freind on here told me that i need a 20pole tach now. Question i have is do i need other cables to hook up new tach? or can i use my old wires that i had from my old tach? thnx in advance for the help
  8. archery1

    help with 90hp force power trim

    I have been searchin internet on how to drain then fill my power trim. it is a single cyinder system. I has a knurled bolt towards top on side.. then a hex head(female) screw on lower part of cylinder. I am pretty sure i loosen kunrled bolt on side to fill but do i loosen that bolt that takes a...
  9. archery1

    force motor

    I have a 90hp force otboard, the tag on mont is unreadable. how do i find out the year? The reason i am askin is i need to buy a impeller and thermostat for it. Frank from on this forum put the motor on 7 years ago , And as we know Frank has passed away in march of this year. He did work...
  10. archery1

    2 diagrams ...please????

    i recently bought a new trolling motor..and fishfinder.... now the t. motor is a 24 volt... so i need diagram to hook the batteries up... and also.. can i hook my 12 volt fish finder up to them without hurting it? if so how? thanks for anybodys help on this,.. i dont want to hurt my new setup
  11. archery1

    help with a 1997 40 force motor??

    my motor has 2 coil packs.. if i hook a dvm meter up to each one seperatly.. whats the reading i should get from them? i think my 1 coil pack is going bad but want to make sure what resistance they each have so i can test them before i buy new.
  12. archery1

    can anyone help with this

    i own a 1997 40 force outboard it has a miss in it.. now i need to no how many trigger coils the stator has ?and my motor has 2 coil packs ..what resistance of ratings should each one put out ? i think one of the coil packs are goin bad but need numbers of outputs so i can test mine out...
See more
Top