Recent content by ArneA

  1. A

    fastwin choke solenoid

    Would any of you folks have a bone yard of fastwin parts, 1969 fastwin choke selonoid is what I am looking for...Found one on ebay but the guy must have gold plated it because it was quite costly. Thank you
  2. A

    Plug type

    1964 Evinrude 18hp..Charts call for two plugs,,a B6S and a B8S NGK....Can someone tell me the difference and which plug is recommended for the Fastwin 18HP ?
  3. A

    Stumped by an O ring

    1964 Fastwin 18hp long shaft Evinrude.. Just put the water pump impeller in and the housing screwed down tight. In the parts manual for the Evinrude Gear case group there is an O ring identified as part number 11in the 1964 parts diagram.. On the 1963 parts diagram it is identified as part...
  4. A

    18hp fastwin impeller.

    I guess that when no one responds within a few days, my question was dumber than a fence post or no one wants to take the time to help. I am persistent though, so lets try again.. Looking for a service manual for 18hp longshaft evenrude fastwin. Would like to change the impeller but not sure how...
  5. A

    1964 service manual for evenrude 18hp

    Would like help with directions on how to change the impeller on my evenrude 18hp long shaft motor. Would like also to download a service manual for this motor. I am guessing that it is a 1964 as best I can guess...The serial number is 18403D-E01810. Thanks for your help.
  6. A

    Thank you

    Thank you Iboats friends...I was looking for a tiller grip and through your help and referrals I finally was able to fine this "hard to find" part. Thank you so much for the wonderful resource that you are. Arne.
  7. A

    Cant find a part

    After going to ebay many times and to craigslist many times, I still cant find a part that I need to locate. If someone can help out with this, I would appreciate it very much...Looking for a tiller grip. Just the plastic end that is griped and turned for speed control...1956 AD 10 7.5 hp...
  8. A

    Exhaust Housing Gasket

    1956 7.5HP AD-10M Received my new exhaust housing gasket #18-2894-9, (replaces OMC 304314) ordered from Iboats. The last time I replaced this gasket it came with one side of the gasket covered with a sticky substance. The new gasket does not have a sticky side. Do I need to use some...
  9. A

    Impellar placement

    1956 AD-10M. Replacing the impeller and now that I have it out and have ordered a new one, I cant remember which way the impeller fins are bent when placing it in the housing....Does anyone know of a video that would show which way the rubber fins are bent or can they be bent in either...
  10. A

    Fuel fitting

    1956 Johnson AD10M 7.5hp. About 8 months ago I reconditioned this motor and sent the male fuel fitting to someone in the club to have it rebuilt with new o-rings. I have forgotten who it was now but that is not important. I have started the motor twice now and when disconnecting the fuel...
  11. A

    AD10M prop

    Can someone please direct me to a chart that gives the proper prop diameter and pitch for the 1956 AD10M 7.5hp Johnson. I had located a chart previously but cant seem to find it again. Thank you.
  12. A

    recoil

    Can someone kindly tell me if a recoil assembly from an AD-!! will work on my AD10M? I have located an AD-11 assembly but when going to marineengine.com, there are no parts numbers for the AD-11 so I cant match them up to see if it will work on my AD-10M. If it will work on my motor, my 3...
  13. A

    vintage parts

    Haven't been able to find a link on this site where a person can search for a vintage part or list parts that are needed to complete renovations. Is there such a place on iboats?
  14. A

    recoil starter

    Its really frustrating. I have been waiting for three weeks for a guy to send me a recoil for my 1956 7.5hp AD10m and the part finally arrived today......Wrong !! The box had an Evinrude recoil that didnt even fit on my AD10... So I am back hunting again. Found one on ebay tonight and the...
  15. A

    which way is up?

    Reassembling my AD10M and the Johnson parts catalog shows two parts that I have forgotten which way they go in. It is in the Gearcase Assembly Group, part numbers 5 and 6. The diagram is a little fuzzy for me to see. Does part number 6 go in cup up or cup down? I am assuming that it goes cup...
See more
Top