Has anyone had a shop give their boat a paint job? I have an aluminum crestliner and would like to get a new paint job for it. Any reccomendations, advice, etc.......
Has anyone had a shop give their boat a paint job? I have an aluminum crestliner and would like to get a new paint job for it. Any reccomendations, advice, etc.......
Does anyone run or heard anything about the stainless steel solas props. I want to put a 13x19 on my 115 johnson and wanted to know everyones opinion about this brand of prop. My stock prop is 13 7/8x19. Putting a little smaller diameter prop on(13x19) won't affect my motor a whole lot will it?
Does anyone have any input on solas stainless steel props? Do you use one? Are they any good? Did they improve performance? I am looking at a 13x19 SS solas to put on my 115 johnson. Any input would be valued and greatly appreciated.
I have a 1996 johnson fast strike 115 horsepower. I want to select on of the hustler props for in but know I have to get the hub as well. For these years of motor (1996) they have an option for a 13 tooth spline (1973 and newer) and another for a 1996 and newer 15 tooth spline with a v6...
Allright, does anyone know of an aftermarket aluminum prop I can put on my bassboat that will make it a lil faster? Any suggestions or companys that sell aluminum props that are a step up from oem would be appreciated. Also, if anyone is running these props, have they achieved a greater top...
I have a 115 hp johnson v4 on an alluminum bass boat. The stock steering kit is a single rack and pinion. Should I opt for the double or replace it with another single? Also any pros and cons to the teleflex no feedback systems? The boat runs right at about 50mph. Is that pushing it for a...
Allrighty, here goes. My 17'6 bass boat has a 115 v4 1996 johnson fast strike notor. it currently has a single steering setup, but it's now shot and needs replacing. It seemed to do just fine with the single setup. Should I opt for the doubleor do you think the single will be just as good...
Allrighty, here goes. My 17'6 bass boat has a 115 v4 1996 johnson fast strike notor. it currently has a single steering setup, but it's now shot and needs replacing. It seemed to do just fine with the single setup. Should I opt for the doubleor do you think the single will be just as good...
I have a question regarding steering and steering cables. I have a single cable steering setup, I believe something may be lose or damaged. In regards to the steering wheel, are their teeth that that could be missing that causes an excessive amount of play in the wheel? It feels as if their...
I have a 17'6" crestliner aluminum bass boat with a 1996 johnson 115 fast strike outboard. Hers the problem. At higher speeds, say 20 or more mph, the steering begins to loosen up and the boat starts to wobble back and forth, exclusively in the back end. The motor itself seems to be moving...
What would yall reccoend for a 1996 johnson fast strike 115 hp on an 18 foot bass boat. the current prop is 13 7/8 x 19. Any suggestions for increased top end etc..... stainless or alluminiun?
The stock prop on my 115 hp v4 1996 johnson is 13 and 7/8 x 19(diameter and pitch). Would replacing it with a 14 0r 14 1/4 diameter and keeping the 19 inch pitch make much of a difference? The performance was well with my old prop, but am looking at a hustler on ss prop and most are not...
I am looking to replace my stock 3 blade alluminum prop which was 13 7/8 x 19. It came on a 115 hp johnson fast strike motor. I want to get the hustler aluminum 14 x 19. Will this work ou allright and do I need to get a new hub housing with this prop or will the old pieces work and match up...
My stock prop is 13 7/8 x 19. It's on a 115 hp johnson fast strike motor. Seems the closest match would be a 14 x 19, more than likely aluminum due to the cost. Would this make much difference and what I be able to use the stock hardware when mounting this prop?
