Recent content by bassmanhb

  1. B

    1993 40hp force Loose Wire.

    Legal, so where does #5 go?
  2. B

    1993 40hp force Loose Wire.

    Yup, but the problem is I need to know where it connects as I can't see/find it. That's why a picture would help immensely.
  3. B

    1993 40hp force Loose Wire.

    Ok , circled in yellow is the wire in question. Where/what does it connect to? I can't find it on any of wiring diagrams anywhere lol. Thanks
  4. B

    40hp force outboard owners. year? And wire question.

    Here is a pic of the wire. Legal, thanks will look it up.
  5. B

    40hp force outboard owners. year? And wire question.

    Jerry, wires not cut off still has the end on it. Just cat find where it goes! Driving me nutz! Lol
  6. B

    40hp force outboard owners. year? And wire question.

    Lol, thanks. That's what I'm trying to figure out! Can't find it on the schematics, and can't see where it goes to in pictures of this outboard.
  7. B

    40hp force outboard owners. year? And wire question.

    Roscoe thanks! Looks like it's probably the same year as the boat then, which is a 1993. Appreciate the help .
  8. B

    40hp force outboard owners. year? And wire question.

    Yup, on both. The wire isn't attached to anything for the high temp warning so need to know where it goes? Any idea on figuring out the year?
  9. B

    40hp force outboard owners. year? And wire question.

    Just picked up a pontoon that has a 40 hp force on it. Problem is the serial number/year sticker is missing and I need to order an impeller for it. Any other way to determine what year it is? Also in the attached pictures the wire shown, where does it attach? And other picture where does the...
  10. B

    Oil pump arm alignment.

    Hello all, been awhile and have a question about aligning the oil pump arm with factory mark. It should be easy but the arm on my pump has 2 Marks! And I am not sure which mark to use or if the arm should be in the middle of the 2 marks.... it's a 1995 90 hp mercury..... any help would be...
  11. B

    replacing old 2 part trim and tilt with seperate pump inside boat .

    hello all, just wondering if anyone can help me with this, i have a 1981 mercury 80 hp outboard that runs great, that has an external TnT pump and 2 rams on the engine that has all the hydraulic lines going bad .... instead of replacing the lines which arent cheap. can i replace it with a used...
  12. B

    epoxy or poly for bow/keel reglassing ?

    hello everyone, been awhile since ive been on the forums ! just picked up this little ranger bass boat that in great original shape..... except for the beach rash, keel dings/gouges ..... transom is good and dry (drill test) same as the stringers. whoever had the boat before me hit the trailer...
  13. B

    *new title* hole repair and new floor and decking

    hi everyone, just bought a another boat nothing fancy just a 16 ft mirrocraft super fisherman sc with a little 35hp Johnson motor... well normally I would take the boat out and test it on the water before buying, but in this case I couldn't and was assured it was in good shape and only had a...
  14. B

    sleekcraft 26' wish i had the money and place to restore this ;)

    after seeing vegas and others restore these sleekcraft boat i have really began to like them .... just saw this one on CL but dont have the money or place for such a big boat but love the looks of them link= http://appleton.craigslist.org/boa/2507318534.html maybe someone else might like...
  15. B

    stainless steel bolts to replace old oversized/repaired rivets ?

    hello again everyone i have a quick question for the people WHO HAVE ACTUALLY USED STAINLESS STEEL BOLTS IN THEIR BOATS TO REPLACE BAD RIVETS . see link to boat here= http://forums.iboats.com/showthread.php?t=440708 ive done a couple of hours of searches and have found eaqual number of people...
See more
Top