hi I had another article but no one replied after a while with help.. as this engine I cant see there are no adjustments for fuel to run lean or rich..
I did the 2 finger test the one guy mentioned you stick 2 fingers in each of the 4 barrels.. and the bottom right was only one that picked up...
hi I have a 40hp 402 engine..
I put a new carb kit in... I checked the filter its clean I checked spark I got lots
but the engine doesn't wanna idle and when I rev higher in neutral she hickups kick backs and cant rev fast... what be wrong what can I do
I even adjusted the idle screw best I...
hi
I have question I tried to research as I been told I can not use a a deep cycle battery on an outboard engine as it uses a rectifier and burns them out... or I cant use the mini kota dual battery charger... charges 2 batteries off the boat engine.. but I think I can but I was told you...
hi I tried to re reply to the topic but its closed and guy said its a sticky but its not doesn't sit on the top
but I wanted to know so a washer goes on and does it sit tight... and is it supposed to be tight the cap... and when I do get it off.. I got the 2 needle valve kits.. the
o...
hi I testing my engine last year I set the WOT to do the timing and it seemed to run fine last year
now I just finally got to run it wanting to put it in water tomorrow... and the RPMS with the cover off is 400rpms and when I put the cover on it idles 200rpms and then just shuts off after a...
hi
I have 1978 charger 115hp the hydraulic lift body module was leaking out the line person had it before cross threaded it... I was able to get one off a different engine from a boat wrecker place... it lifts and lowers the unit and no leaking from the lines....
but it cant hold itself...
hi i have the 1978 115 chrysler outboard.. i got it with a leaking power trim body.. i have tried tighten the 4 stainless pipes going in it but not luck i even tried teflon tape on the threadings.. and one of them doesnt tigthen up what be causing it to leak and i guess the one is stripped...
hi i took the lower unit apart and trying to get the shift rod out unhooked from the cotter key inside the lower end i straightened the cotton pin basiclly with long needle nose plyers but i cant pull it out i tried using a hook scriber and to pull it up through the loop at end all it did...
hi i working on the lower end something is broken in the bottom half of gear box it doesnt shift so i took it off but i also wanna remove the water pump cover but it cant as the arm still attached... do you need to pull the top engine off to get at that linkage as i cant see how you can...
hi i havent gotten my block back from the machine shop so i just asking questions ahead of time
i read online you test the timing when engine is running but if its out of wack it might damage things.. and i having new pistons put in so dont want that
now on my 115 chrysler engine i set the...
alright i asked in a differnet topic but figured i should write a new head line
as i like to know what years it covers? off boats net you can get 79-81 they use the same gear housing... but i learned there are superceeded parts
are there any other years... what are all the years that a...
i forgot to scribe the first 2 pistons rods but the last 2 i was doing i tried to scrib on it and us center punch it didnt work so i just push them out
but how bad is that? and is this bad since i dont know which way it goes then?
this is off a 79 115hp johnson
hi i bought a 79 115hp johnson for the crankshaft as the marina said the 79 and 84 are the same crankshafts just have different numbers
but i wanna know is the block exactly the same?? as i was going to have the 79 repaired have 1 cylinder bored instead of 2 like on the 84.. and i was...
oh another issue just showed up not sure if its bad or if that's normal I just spun the prop by hand and there is a clanging sound is that normal???
here is a link to my video of the prop
http://youtu.be/HaS2gh6ZG54
but if I spin the prop other way doesn't clang loud
hi I deciding to re wire my boat to put the batteries at the front of the boat since they be out of the way instead of battery boxes at the back, but I wanted to know how many amps does the starter use as I was going to use 4 gauge booster cable wire and just cut it up
this is for that...
