Recent content by csisommout

  1. C

    How to replace temp switch

    I have 1997 40hp with s/n 0G565379. I want to replace temp switch 87-16775A3 was mounted on block. How do I remove it. Thank you for any ideas
  2. C

    Alarm beeping

    Looking for some advice, I have mercury 1997 40 hp 4 cylinder oil injection, with S/N 0G565379 , when starting motor alarm keeps on beeping even after disconnect tan wire from sensor and replaced low oil alarm module. Any info will be appreciated, Cal
  3. C

    Merc 1997 40hp 4cylinder solenoid check

    Hi, everyone out there, I have Mercury 1997 40 hp 4 cylinder oil injection, what am I supposed to read when I check out solenoid with ohm meter red probe to yellow wire black probe to black wire, when I do that it red opened 12ohms low resistance, I also check it with volt meter when turn key...
  4. C

    Mercury 40 hp mixture adjustment screw

    Hi, I have 1997 40hp 4 cylinder 2 stroke, s/n 0G565379, nood to locate mixture adjustment screw, Thank you 4 info
  5. C

    1997 mercury 40 hp 4 cylinder 2 stroke

    I have Mer 40hp 4 cylinder run hot at startup, water peeps okay,seems to be high idle also.please help
  6. C

    full advance spark timing setting for 1990, 50 hp?

    hello, all experts I have 1990, 50 hp, 2cycle Evinrude, model #VE50BELESR, S/N G02535055. I replaced power pack with conversion kit(113-4489) the instructions say to reset ignition timing to the service manual. does anyone know the full advance spark setting for this motor? any info will be...
  7. C

    Evirude 1990 50 hp, fuel pump?

    Hi, everyone. I have 1990 Evinrude 50 hp having a hard time starting until spraying some fuel into the carb. How do I verify if my fuel pump working normally? what is this called? the orange tab should be down or up? thank you.
  8. C

    RPM at w o t only go up to 3000 rpm?

    Hi, experts out there. I have Evinrude 1990, model# VE50BELESR, SERIAL # G02535055. After replacing power pack with new conversion kit {113-4489), I do the run test at first couple times at w o t, it seems to be normal seeing RPM at about 5500 for a while, after that when warm up, It seems to...
  9. C

    where to refill trim cylander on 1990 50 hp?

    I have 1900 Evinrude 50 hp 2cylanders, 2 stroke, Where do I refill the fluid? and what kind of fluid does it need? It is stuck , used to get it up and down by hand. now it is a lot harder to lift it up by hand. Model #VE50BELESR , S/N G02535055. Thank you for any suggestions.
  10. C

    Throttle plate won't return all the way back?

    Hi all experts out there, I have 1990 Evinrude 50hp, 2cylander, 2 stroke. I replaced ignition pack under flywheel after tightened 6 screws for top plate and bottom plate together, then I check the control handle by advancing it all the way and return it to the neutral position my throttle...
  11. C

    1990 evinrude with s/n G02535055 pwr pack dva output?

    what would be the voltages from pin #1 and #2 from pwr pack when engine runs? thank you.
  12. C

    Techrom metor

    Hi, any one, I have 1999, 30 hp, Mercury with oil in jection. There is 1 connector from side control. Is that for techro metor? Thank you
  13. C

    Won't above 1500 RPM when in gear or out off gear?

    I have Evinrude 1990, model# VE 50BELESR, when gives it more fuel it dies. checked compression 119, 221 psi, pulled out carbs and cleaned them also checked spark jump at 7/16 of an inch seem to be okay but whem pull out either spark plug boot it dies, run out of ideas. where do i need to start...
  14. C

    choke level works?

    Hi, any expert out there. I have Mercury 1999 30hp. 30E0, serial#06762519, oil injector. having a hard time starting cold, when i started it at home with muffs it take a few cranks only, when i took it to the lake it takes about 10 times to get started. is there any adjustments does it...
  15. C

    How to remove steering tube from 1999 30hp.

    I just bought Mercury 1999 30hp oil injection, with rusted steering tube can not slide a steering cable through. thank you.
See more
Top