Current visitors

Home
Members

cyclops222's latest activity

C

cyclops222 reacted to Scott06's post in the thread Cold Starting RPM: What is normal? with Like.

when adjusting idle speed take the throttle cable off the carb . Adjust the idle speed. When you reattach the throttle cable adjust so...

Apr 27, 2025
C

cyclops222 replied to the thread Need help, overheating at cruise rpm.

Also check the thermostat parts. Stat in heated water of a stove pot, gasket shape and location. If a gasket is there does it look...

Apr 26, 2025
C

cyclops222 reacted to Sprig's post in the thread Skinny water day. with Like.

Just a word of caution, never let your dog ride in the bow when under power. They can easily get thrown out resulting in death or...

Apr 25, 2025
C

cyclops222 reacted to DeepCMark58A's post in the thread Weed control with Like.

I have a set up that I use on the bottom, an 80 gpm pump to flush out the silt from around the dock, I may try jetting the roots out...

Apr 25, 2025
C

cyclops222 reacted to dubs283's post in the thread Green people destroyed another fantastic fishing area. with Like.

I'm curious as to how balanced the river ecosystem was prior to septic system daylighting into riparian areas. Void of life? A sound...

Apr 25, 2025
C

cyclops222 reacted to MikeSchinlaub's post in the thread Primer for engine block? with Like.

I've never painted a block, can't recommend a specific product. I can tell you that self/acid etch primer has been replaced by direct to...

Apr 25, 2025
C

cyclops222 replied to the thread Ideal prop - 28' Landing Craft - Twin Seapro 300 AMS.

Your props are determined when you have a FULL LOAD of stuff and people in the barge. Empty barge ? The captain & rev limiters will...

Apr 25, 2025
C

cyclops222 reacted to Grub54891's post in the thread 5.0 GXi-J fuel pump relay keeps tripping with Like.

If you have way to much trouble getting the pins out, how about getting another relay socket from the local parts store, snip your wires...

Apr 25, 2025
C

cyclops222 replied to the thread Excessive Oil/Grease by Alternator area..

You have a serious case of water being sprayed all around the engine.

Apr 25, 2025
C

cyclops222 reacted to todhunter's post in the thread Repair before installing Keelguard? with Like.

Grind out the bondo, fill with thickened gelcoat, sand to rough shape, roll on some gelcoat, then install the keel shield. I did this on...

Apr 25, 2025
C

cyclops222 reacted to bajaman123's post in the thread Repair before installing Keelguard? with Like.

Fix it right before putting on the keel guard...would be my suggestion.

Apr 25, 2025
C

cyclops222 replied to the thread Low speed jet adjustment.

Have you removed the idle needles to see if they are damaged /

Apr 25, 2025
C

cyclops222 reacted to Vic.S's post in the thread Low speed jet adjustment with Like.

As you screw the needle in the spring will compress. Screw it in only as far as necessary to very gently seat the needle. Then unscrew...

Apr 25, 2025
C

cyclops222 reacted to Mc Tool's post in the thread Low speed jet adjustment with Like.

Have you balanced the carbs....so all three are opening at the same time. If you have one carb opening before or after the others you...

Apr 25, 2025
C

cyclops222 reacted to Scott Danforth's post in the thread Pointers on replacing Flywheel with Like.

No need to replace the flywheel. just spend the $15 on a ring gear

Apr 25, 2025

Show older items

Home
Members

Top