I have a 26' Grady White w/ twin 200 hp Yamahas. Carbuerated , oil injected 2 stroke. Ran fine all year and all of a sudden when i idle it will idle rough and stall.
Top end and pick up are fine. If it is above 800 rpm she runs ok. I turned up the idle to about 800 in neutral which helps but...
I have a 1996 grady white w/ twin 200hp yammi's. I took it in for a tune-up last spring and the marina
adjusted the link and sync. They checked compression and everything else. The one motor seems to smoke a
little more than the other. How do i know if the oil injector is "leaking" a little...
Help, I had my motors tuned this winter. Mechanic said compression and everything else was fine. He said he did a
link and sync. I am assuming he adjusted the carb linkages and sync the timing. No parts needed. Engines ran great first
3 fishing trips. On last outing i stopped for fuel on...
Hi All,
I have a 93 Force 120 hp outboard. Sometimes at idle it will be reading 12.4v and running rough and then it will jump to 13.8 volts and go up to 14.1 volts and then idle fairly smooth. When I shut it off and restart it it will be back at 12.4 volts.
It may not go back up but stay there...
Hi all,
Kinda stupid question about my trim but......this is the way I bought it.
93 Maxum 18' bowrider. When the motor is tilted/trimmed up the center cylinder
should extend and when it is out all the way the tilt cylinder should tilt the motor up
and out of the water. Mine actually tilts up...
I just bought a stator online for my 93 120hp outboard. I bought the exact part number from the manual
and it is a 20 pole stator. I just pulled my flywheel of the motor and the one on the engine is completely different.
It is black epoxy covered and only has 12 poles and has the number...
I have a 93 Force 120hp OB. A repair shop just rebuilt my carbs and fuel pump and got me running.
She screams at top end at 5000 rpm but when it idles in gear it kind of lugs and stalls. It will start
but you need to throw it in gear and jump on it to get her going. The mechanic said that it...
One of my twin 200's is idling rough and also seems its not revving up like normal.
Any hints at checking for simple electrical problem like a bad coil or a plugged idle
jet on a carb. thanks for any insights.
Dave
I bought a 95 Maxum with a force 120hp outboard from an estate sale as is.
The outboard was tilted up with a bracket under the motor that went through
the holes on the trim bracket. I figured out to take out the hitch pin and pull the bracket
out to free up the motor to tilt up and down. The...
My carbeurated, oil injected 200 hp Yamaha has just started idling a little rough. When it idles you can hear it sputter or
spit once in a while. I changed the plugs with new NGK's but it made no difference. I think it may be a bad coil but not sure.
Does any one have any ideas how to narrow...
I bought a boat that sat for six years. When I finally got it started it had no power at WOT and bogged bad.
I replaced every electrical component on the engine, stator, timer base, brain box, rectifier and coils. Timing is at 20 btdc.
I also boiled out and rebuilt all 3 carbs. The engine...
I just bought a 16' bass boat w/ a 1980 70 hp Johnson. It has a pin on the bottom bracket and a single cylinder
mounted on the bracket on the transom. When I have it on the trailer bracket and lower it down at the ramp to run it in the water how do I get the bracket to latch on the pin or do I...
I have twin 1995 200hp salt water series 2 stroke o.b.'s One seems to smoke more than the other when I am trolling on one motor. I switch back and forth every hour.
I troll probably at 700 rpm.
How do you adjust the oil injection on this motor to see if it is running too rich
or is it is just...
I have a 27 grady white w/ twin outboards. The hydraulic steering seems "mushy".
I have to turn the wheel at least a 1/2 turn to get the motors to start turning.
How responsive should the wheel be? Seems like it always been that way since I have had the boat.
I have a 1970's vintage merc 9.8hp. Does anyone know how to correctly tilt up the motor.
Do you just put it in forward gear and pull up? Also there is a little lever that says troll that
is on the pivot bar under the front of the motor. What is this for and how does it work?
thanks for any...
