Recent content by downjigger

  1. D

    Purchasing an E-tec

    I need some feedback from E-tec Owners. I'm looking to purchase a new boat and motor soon. I have had my mind set on an E-Tec since they came out. Yesterday a dealer (sells Yamaha) told me that the E-tec would have substantial vibration at slow spped. I mostly troll fresh water and have...
  2. D

    Lower unit Parts needed for 72' Evinrude

    Hi Guys- I've been rebuilding my 1972 65 HP Evinrude. It has the "selectric" electric shift. Alls you need to do, to see why you hear people brag on these motors, is to take one apart. Great engineering to say the least. My problem is I need a reverse shift lever that goes on the the oil...
  3. D

    1972 Hydroelectric shift-mechanical question

    I'm about ready to buy a new lower unit for this motor(1972 Evinrude HydroElectric 65 HP) just from frustration!<br /><br />Here is what is going on. I have thoroughly checked all wiring switches solenoids etc and believe they are all working properly. I have been on this forum reading all the...
  4. D

    should there be oil on shift solemoids

    When I removed the shift solenoids on my 72 65 Evinrude hydro electric shift there was gear oil on the solenoids, plungers, wires etc. Is this normal?
  5. D

    evinrude shift solenoid and shift switch

    I removed the lower unit on my 72 Evinrude to check solenoid wires. I found a bare wire that apparently shorted things out. If I apply 12v power in the proper sequences will it shift while turning the the drive shaft by hand?<br /><br />Also, what should the ohmmeter be reading when I test these...
  6. D

    shift solenoid test

    I removed the lower unit on my 72 Evinrude to check solenoid wires. I found a bare wire that apparently shorted things out. If I apply 12v power in the proper sequences will it shift while turning the the drive shaft by hand?<br /><br />Also, what should the ohmmeter be reading when I test...
  7. D

    72' 65 HP Evinrude has water in bottom cylinder

    Need some advice to be sure-<br /><br /> Just put this motor in water for first time since restoration. Bottom cylinder is getting water. Head Gasket was new and okay and cylinder has same compression as other two at 140-150. Is it possible for water to get in cylinder from exhaust side? I...
  8. D

    115 HP Mercury is not coming up to speed

    My fishing buddy has a 1994 (approx) 115 HP 6 cyl Merc. He started it this spring and it ran fine in the barrel. Took it to lake and it started fine and would rev in neutral but when he put it in gear he could not get any speed. During spring startup he had to replace a blown 20 amp fuse on...
  9. D

    Can my '72 Evinrude 65 HP have power trim

    I am trying to find out if I can add power trim/tilt to my 1972 65 HP Evinrude Triumph? I know I can buy aftermarket products but would like to know if there is an OEM part that I can add. Model #65273S Serial Number 010559. ALso it is painted with the anniversary Gold color so would want to...
  10. D

    Looking for info/source for an Evinrude DuckTwin

    I thinking about building a duck hunting boat this year and would like to power it with an Evinrude DuckTwin. I know little about this motor, other than there was such a thing, and would like to consider using one for the project. Any info concerning specs, source etc would be great.
  11. D

    Applique for 1972 Evinrude Triumph

    Hey Guys- does anyone know a source for the appliques that apply to the front and rear of the cover for a 1972 Evinrude Triumph 65 HP that is nearly restored to like new condition. I also am looking for a source for the cover seal(gasket).<br /><br />"Keep on Trollin"-Downjigger
  12. D

    Joe- do you have any remote controls?

    Joe-<br /><br /> Do you have nay remote controls for the 1972 Evinrude Triumph 65HP? How about any Cover gaskets or paint. Youv'e probably heard these questions before.<br /><br />Thanks, Paul D
  13. D

    1972 Evinrude Catalog

    I'm looking for a catalog (pictures on line would do)for Evinrudes 1972 product line. I am restoring a 1972 65 hp Triumph and would like to see original color and specs.
  14. D

    1972 Evinrude Triumph 65 HP

    I am restoring this motor and could use some info on where to find very good or new condition parts. I need a cover gasket, appliques, decals and anniversary Gold paint. I also need remote control parts that are in good condition like wire harness, covers, shift or anything that will help this...
  15. D

    Looking for Specs on 1976 Evinrude 70HP

    Can anyone suggest where I might find specs on a 1976 Evenrude 70hp
See more
Top