I've looked everywhere I can think of and I can't find anyplace with a good selection of boot stripe tape. I would like to get a two tone as one piece. Anybody now who supplies this??<br />Thanks
Mercruiser 4cyl. 190. My problem is when I try to start the engine after its been running awhile. We'd been out fishing a few hours and thought a line was tangled on the prop so I shut it off tilted it up....no problem. Then I went to crank it and it would barley turn over. I thought the battery...
I managed to spray the Imron paint on before the weather got cold. I just picked up the plywood for the floor from a friend that coated it with 1 1/2 oz. for me. That will be next.<br /><br />check the photos out at http://albums.photo.epson.com/j/AlbumList?u=4063544 <br /><br />
<br /> <br /><br />$1700<br />1988 90hp Johnson. motor runs perfect. <br />Shoreline ez-roller trailer. Needs new tires if you plan on going on frequent long trips. This trailer works great with this boat, It takes me about 1 minute to put the boat on and about 3 seconds to push it off. The...
<br /> <br /><br />$1700<br />1988 90hp Johnson. motor runs perfect. <br />Shoreline ez-roller trailer. Needs new tires if you plan on going on frequent long trips. This trailer works great with this boat, It takes me about 1 minute to put the boat on and about 3 seconds to push it off. The...
I pretty much have the floor cut and dry fitted. I fit the two fuel tanks in, the bottom of the tanks sit about 8-10 inches below the floor. Next is to cut the hatches into the floor. I used 3/4" Exterior (not exposure-1) A-C grade douglas fir 5ply. CDX plywood uses the same waterproof glues but...
I've notice most boats have a thru-hull fitting on the stern of the boat (usually with a mesh gaurd on it) for live well pick up. My concern is when you under power the fitting will be dry. If I have a 30 mile trip offshore my bait will die. I was thinking of putting an intake strainer on the...
I've notice most boats have a thru-hull fitting on the stern of the boat (usually with a mesh gaurd on it) for live well pick up. My concern is when you under power the fitting will be dry. If I have a 30 mile trip offshore my bait will die. I was thinking of putting an intake strainer on the...
I had never tried it before but spraying "pledge" or similiar allows the last coat of resin to dry completely. The spray wax did an excellent job and its very easy, cheap and convienient.
I have a 1986 Mercruiser 4cyl. 224cui. 190hp<br />I would like change over from the points. I also see pertronix has two models available. Has anyone had any experience with it?? I also need to find out if its available for my motor.
Since I didn't get one for x-mas. I might as well buy it myself and get a good one while I'm at it. I understand the antennae is most important. I want a mounted unit, waterproof would be nice.
Johnson v4 90 hp.<br />I don't have a manual for this motor.(I get it from the library when I need it).Anyway I ran a compression test on the motor today. It pumped up to 120lbs. seems low to me. I'm going to sell it soon and want to be able to tell someone that the motor is fine or not. Also...
I did some work on my project boat and removed the port & starboard tanks. The port tank has a few hole in the top and the fill neck rotted off. The other tank looks good. I'm wondering what I'm going to do for replacement a replacement tank. As it is each tank is 25 gallons.I have a 1986...
Well no I need a new fuel pump for my Merc.<br />100 bucks. I was gonna put a electric fuel pump on it,(much cheaper). Any ideas about it? The manual says 5-6.5psi so thats not a problem. The only thing I'd have to do is make a block off plate. Off hand I can't think of a reason not to do...
