I bought a new diode because my engine keeps going inot SLOW mode after it sets for a while. I think the Diode is bad, I have changed the powerpack, spark pluf wires, both temp sensors, I cant find any wires grounding so I am thijking its the $12 diode causing the issue but I cant find it in...
I bought one the other day bit the sticker on the font plate was ripped so I cant see the bottom dial information. I need to know what that dial is for. A photo of the front sticker would really help.
Thanks in advance.
JD
This is what my sticker looks like. Help please.....
The alarm is going off though causing the engine to go into S.L.O.W mode after I am at wide open throttle for a while then slow down. The engine clunks, like it kicks in and out of gear and wont go past 2300 rpms.
If I turn her off and restart the alarm goes off and she goes full steam ahead...
I've got a 1993-95 evinrude 175 looper. I'm not getting spark on the STARBOARD side of the engine. I checked the stator, it's like new, wires are new, new powerpack, new plugs.
I read somewhere that the temperature sensor being bad could cause this. I need help also about the shift switch...
When I put the engine in reverse it does not have any throttle to go in reverse.
1993 Evinrude 175 Looper Ocean Pro
It also spun out of gear today after attempting to plane off.
Any help on this would be greatly appreciated
JD
My port side head is running cool but my starboard heat is hot.
Work done:
New thermostats
New water pump
New fuel lines
Took off head and cleaned out clogged ports, there were two (top round holes) that were clogged completely and the other ports (around outside edges) were half filled with...
I just put a new water pump and thermostats in my engine. I am not clear on where the water is supposed to exit the engine. I have 2 exhaust outlets by my flush connector but no water is coming out of them.
I posted a video of her running
http://www.youtube.com/watch?v=DeYD-J10uh0...
Does anyone know what sensor this is? Look at the link or image attached.
I hooked it up to my temperature guage but unsure if thats what is for. What is it called? I have a 1997 (I think but not sure since the plate was removed) Evinrude 175 OCean Pro.
Anybody know how ot identity the...
Anybody know where I can get a PDF version of the shop manual for my 1996 TigerShark Monte Carlo 640? They have them for mercruiser engines on this site, those manuals are the best.
I need it to put my engine back together and look up some things about this ski.
Thanks.
Jeff
Need Manual for...
She has a 4.3 litre volvo penta engine with an OMC outdrive on a load rite trailer. Its a 1995 seaswirl striper 21.5 foot walkaround cuddy
I put a bunch of photos and videos of her running to help you with your advise on this boat I am looking to buy.
http://zetal.com/striper/
Thanks in...
I got my engine, the alignment seems to be good but after reviewing the manual for the older engine I put in to replace my newer one I noticed the lock washer needs to be under the engine mount verses above it. Since my engine is in now and the outdrive is all hooked up it will be a pain in the...
Anybody ever have this problem?
I replaced my Gimbal bearing, went to put the outdrive back on and it gets stuff on the Gimbal bearing at the Orings. It wont let me push the outdrive on any further. Im aftraid if I force i wont be able to get the outdrive off in the future.
I have a...
Does anybody have any insight into what I will need to do/change to swap a Mercruiser 140 3.0 Alpha1 Gen2 with a 140 3.0 Alpha1 Gen1 engine?
I have a 1999 Bayliner 1950 with a Mercruiser 140 3.0 Litre engine. I need to replace it. I found a strong running 1989 Mercruiser 140 3.0 Litre engine...
I got a 1999 mercruiser 3.0 with an Alpha one Outdrive.
Can I swap the 3.0 motor with a 3.7L 470 Mercruiser with out many problems?
If I do ,what problems or changes would I have to do to install the 3.7L into my 1999 Bayliner Capri 1950?
I like that the 470 is water cooled.
I was wondering...
