Current visitors

Home
Members

MikeSchinlaub's latest activity

M

MikeSchinlaub reacted to Scott Danforth's post in the thread spray nozzle size for gelcoat with Like.

You need to test. 50/50 is what I sprayed 2.3mm tip Pre-measured and iced down. Have a helper mix as needed.

Jun 27, 2025
M

MikeSchinlaub replied to the thread spray nozzle size for gelcoat.

I have a 2.0 gun that sprays great. I haven't used Duratec, but 50/50 seems like a lot. I think @Scott Danforth has experience with it.

Jun 27, 2025
M

MikeSchinlaub reacted to SlipperyOar's post in the thread 1981 Springbok 18' Restoration/Renovation with Like.

Back onto the trailer, time to finish fabricating the top and corner transom caps and fit them up before painting the transom and then...

Jun 25, 2025
M
MikeSchinlaub replied to the thread Boats from work..

I painted the other one today.
Jun 25, 2025
M

MikeSchinlaub replied to the thread 1989 Sea Ray 200 BR Interior rebuild and new layout.

I really don't think I'm qualified to help with any structural design. Especially when the consequences of failure are someone falling...

Jun 25, 2025
M

MikeSchinlaub replied to the thread 1989 Sea Ray 200 BR Interior rebuild and new layout.

I wouldn't try to glass over the wood with OTF. I've never tried anything like it, but it will likely interfere with the bond, maybe the...

Jun 25, 2025
M

MikeSchinlaub reacted to Crazy_Pilot's post in the thread '89 Arriva 2050 Restoration with Like.

Already on the way. My woodworking neighbour lent me his separator, I have a 20 ft hose arriving today and put a switched extension cord...

Jun 25, 2025
M

MikeSchinlaub replied to the thread 1989 Sea Ray 200 BR Interior rebuild and new layout.

Some of the nicer ones have removable plastic panels around the engine. You can take the whole wall out.

Jun 24, 2025
M
MikeSchinlaub replied to the thread Boats from work..

2 down, 1 to go.
Jun 24, 2025
M

MikeSchinlaub reacted to Scott Danforth's post in the thread Forester Boat with Like.

you are sitting on a project that will cost you to dispose of, or you can dump a lot of money into restoring it. (all fiberglass boats...

Jun 23, 2025
M

MikeSchinlaub reacted to redneck joe's post in the thread TRANSOM ISSUES!!!! with Like.

Well, you know you were new the last time and not sure what you were doing. We've all been there. Now do it right. The whole...

Jun 22, 2025
M

MikeSchinlaub reacted to jbcurt00's post in the thread TRANSOM ISSUES!!!! with Like.

Half redoing a 'repair' that was done poorly yields poor results. You are solely responsible for those aboard your boat. Repair the...

Jun 21, 2025
M

MikeSchinlaub replied to the thread TRANSOM ISSUES!!!!.

Well you can add a single layer of csm to help give it some water protection, but it won't help with water wicking into it from below...

Jun 21, 2025
M

MikeSchinlaub replied to the thread TRANSOM ISSUES!!!!.

The top is usually the last place to get wet, and eater will wick into dry areas. The only reliable fix is to replace the whole transom.

Jun 21, 2025
M

MikeSchinlaub replied to the thread Throttle levers 'stiff' at higher RPM?.

I'm not an engine guy, but have you tried them with the engine off? They might be binding up as they extend. That's the best I can do.

Jun 21, 2025

Show older items

Home
Members

Top