Recent content by N1NE1

  1. N

    Power trim stalling motor (hpdi )

    Once I start getting the boat ready for the season I will check everything. Just trying to get some opinions ahead of time .
  2. N

    Power trim stalling motor (hpdi )

    Yes there is a switch on the side of the motor and one on the throttle control. Yes it’s confusing me too
  3. N

    Power trim stalling motor (hpdi )

    If I use the trim switch on the side of the motor it’s perfectly fine , only when I use the one on the controls .
  4. N

    Power trim stalling motor (hpdi )

    (02 Yamaha 200 hpdi )This could be completely unrelated but ..So at the end of last season I was having an issue with my motor not passing water through the pisser tube . Cleaned it out everything works there now . The rectifier was jammed up with some dry salt. Ever since then when I use the...
  5. N

    Fuel smell after fueling up

    So I got to the bottom of the smell. The fill line has some cracks in it which I’ll replace this week. I only smell it after refueling but while I have the floor apart I might as well. Thanks everyone
  6. N

    Fuel smell after fueling up

    I tested it for about 5 minutes . It only takes about 5 minutes to fuel up so I figured that was good.I smelled nothing after this, it’s only when fueling . I definitely don’t fill it to the point where it will flow out the vent . It’s almost like it’s being vented elsewhere since the smell is...
  7. N

    Fuel smell after fueling up

    So after putting some fuel in my boat I always smell the fumes coming into the boat from under the console and floor hatches . I always air out before driving off. I pressure tested the tank yesterday through the vent and it holds steady at 5lbs. Where is this smell Coming from? I’m pulling the...
  8. N

    02 200 Yamaha HPDI voltage output ??

    I've had my 02 200 Yamaha HPDI motor( 223 hrs)for about 3 years and since then I've always though the voltage output to all my electronics was a little high 17.2v ish,never higher. I always run 2 batteries and keep the switch on "BOTH".Nothing has ever fried or blown a fuse but is this higher...
  9. N

    lowrance elite 7 hdi nav cards

    Hello everyone I have a Lowrance elite 7 hdi unit and am trying to find other card options besides navionics if there are any for this unit.I currently have the navionics gold micro sd and never really liked it. The details on anything other than bay/ocean are terrible.
  10. N

    02 Yamaha 200 Water pressure issue

    Just changed out my impeller,housing,gaskets,orings etc. on a 02 200hp hpdi because it didn't seem to be pushing much water through the p-hole. At idle for long periods I would get the warning buzzer. Motor felt hot when it beeped steady. Its an average steady stream but not strong unless I go...
  11. N

    Wiring diagram yamaha gauges

    just bought a used boat with a Yamaha 200 hpdi and it has the Yamaha gauges for gas,oil,rpm,volt etc. The fuel gauge part stopped working and would like to know if there is a diagram for wiring the sending unit to gauge. Right now there is 2 wires coming off sending unit. I haven't traces them...
  12. N

    2002 yamaha hpdi 200hp info please

    hello, I'm most likely going to be buying a boat this afternoon with a 02' Yamaha 200 hpdi motor on it, 140hours. Anything I should look out for? whats the normal compression to check for? Always been a Johnson/Evinrude guy.New to Yamaha. Any info you can tell me would be greatly...
  13. N

    03' mercury 200hp saltwater series question

    is the 03 merc 200 saltwater series Direct or EFI ? 'Im a johnson/evinrude guy. know nothing about mercs..This motor is on a boat im looking to buy. could you tell me a little about them. They say it has just over 350hrs. no meter. can it be plugged in?
  14. N

    Mercury efi and johnson pre 2004 outboard feedback

    Hello, I sold my boat to get a CC and I'm searching for a new boat 00-06' range . I'm running into alot of 00-04 Mercury and Johnson motors. I dont know much about Mercury since I've always been a Johnson/Evinrude guy. Any feedback on them would be nice. Same goes for the non-ficht 03-04'...
  15. N

    Johnson 200 fuel/oil consumption

    Does anybody know what the normal fuel consumption should be, i went close to 2 miles today and used 17.2 gallons @ 4000rpms. Its a heavy 26ft seaswirl striper w/a with a 98' johnson 200 ocean pro.I always though it was under powered. Fuel has just been killing me. I used 50gal of gas to 1.5...
See more
Top