I have a 1989 100GT Johnson. It started smoking bad and using too much oil, fouling plugs etc.
I found a test for the VRO at http://www.maxrules.com/graphics/VROpics/VROflowchart.jpg
I have leaking from the motor housing and Intermediate housing when I pressurize to the pulse fitting to 15...
Replacing water pump.
What type of glue should be used to glue the stainless cup into the water pump housing? Video said refer to manufacturer, my shop manual did not state what type of glue. I have read that Scotch weld 847 is a good choice, are there others?
Motor is a 1989 Johnson 100HP...
Replacing my shift cable for the 2nd time in 10 years. I used the red jacketed Teleflex TFX 301947-03 each time I replaced it.
Both times I replaced was due to the cable seizing up.
Is there a better option?
Boat is a 1979 Albemarle and the drive is a 280 Volvo.
Do you guys replace these when pulling an engine? I just pulled mine and both o-rings have spots where they are compressed.
I checked yesterday with the Marine parts place and they are special order and takes two weeks! I planned to have motor in tomorrow.
I could just flip them over so...
I'm replacing the bearings in my Bell housing "Flywheel cover" It looks like the drive u-joint yoke sits in the aft axle seal ( the aft seal in the bell housing). While the bellhousing axle seals to engine side seal. Anyway the engine side seal point on the shaft is a bit rusty and I was...
If I wanted to buy a new outdrive, how would I do this? While looking I see outdrive for sale, but they never contain the transom assembly or the flywheel cover etc.
I have found new uppers, new lowers and transom assemblies sold separately, but what about the flywheel covers and y pipes?
It...
I just went to service drive and found water in the drive. I then checked the Bellow by loosening the clamp and milky drive oil came out of the bellow.
The Bellow looked ok, 3 years old. I found a split oring on the drain screw, but I did not notice any leaking oil. I pressure checked the...
I cranked the motor the other day and the bearings started smoking, so Im doing the whole rebuild. Anyone done this before? I searched on the web and found info on other pumps that are similar but were not quite the F5B9. Just wondering if it has a split ring, if the bearings need pressed on or...
johnson raw water pump leaking 5.7 part number 10-24228-1.
Same thing happened 7 years ago, water started leaking around the shaft and I replaced it with a new one. Can I just buy a rebuild kit and fix the leak?
Thanks Eric
I removed my old tired 260hp engine a few months ago and purchased a rebuilt vortec engine to put in.
Im finally at the point where the engine is built and ready to install.
Im just looking for any advice, tricks and tip to make the install go smooth.
Im having the engine installed with a...
What is the cover called that mounts around the crank shaft on the rear of the motor? It's the piece that the rear of the oil pan seals/mounts to. I need one and I do not think I have the common term for it.
Motor is a 5.7, post 86, pre 96. Block casting 14093638
Thanks Eric
I have a Chevy 350 638 block that I had built with Vortec heads installed, I believe the 638 was used in 87-95 350's.
Im replacing an older pre-87 350 that is mounted to an 280 outdrive original to the boat, the one with the intermediate shaft in the bellhousing.
Boat is a 1979 albemarle
Will...
I am finally replacing my old raw water cooled 5.7 in my 1979 Albemarle.
I recieved a REMAN long block and in the process of building it.
I had them build a engine with older block that accepts the mechanical fuel pump and vortec heads.
My first question is baffeled or un baffeled oil pan? I...
First question, Does a 1989 100HP (100GT) Johnson outboard come with an alternator?
2. does anyone know of a good repair manual for this outboard?
3. should the outboard let out a chirp to test the warning horn when the key is turned?
Thanks
Eric
So I have a 1979 volvo 350 in a 79 albemarle. It's done!
I was just offered a mercuiser 350 from a friend for a very good price, free!
I need to go over and see the engine and find out the details, but what if any problems will I have?
I know Im jumping the gun by asking questions...
