I have a 1995 Evinrude 175hp that I am getting a one second alarm after cranked. It only happens once or twice on a fishing trip. And it only beeps one time after its started. Not talking about the system check beep when you turn the key to the on position. And the motor is still in neutral. Any...
I am finally going to install a water separator on my 1995 175hp Evinrude. My question is what fuel flow rate do I need for my motor? I see most separators come in 30, 60 and 90 gph. Is it worth getting one with a clear bowl on the bottom?
Also what is a good brand to get. I read where the...
I have a 1995 175hp Evinrude that when I put it in reverse the motor wants to kick up. It started when I had a bad battery and tried to lower my motor. When lowering it will bounce up and down as it got lower. I can even grab the lower unit and raise it about 4 inches. Need some ideas where to...
I have a 1090 8hp Suzuki that idles fine but at wot it does not get to top rpm's. Took it out the other day and where it used to push my boat 15mph it only goes 8mph now. At wot it sounds like it wants to get up to speed but doesn?t (sounds like it?s missing). So I pulled the carb and took it...
I have a tandem axle boat trailer that I just replaced the front axle. When I took the axle off I noticed that one of the springs were broken. Bought a pair from tractor supply for $30 each along with some new straps and spring bolts. I had a guy in Beaumont make me a straight axle. When I...
Does this mean my motor mounts are gone? If so how can I get to the back side to replace it? Motor is a 1995 175hp Evinrude. I am already having to replace the steering arm.
I have a 95 175hp evinrude that I was getting ready for this years fishing. I raised the motor and saw this.
Is this bad enough not to use the boat? How bad is it to replace? What does that bolt bolt into?
Thanks,
Robert
Just put the new axle and springs on my tandem axle boat trailer. I have never repacked bearings so do not know how tight to tighten the castle nut. So I put the hub on and hand tightened the castle nut and spun the hub for a while. Unscrewed the nut and retightened it several times to get...
I pulled my hubs and bearings in order to replace my axle. I just replaced my bearings two years ago so I don?t need to change them. The guy at the trailer shop said to make sure I put the exact bearing back where it came off. Does anyone know if this is true? I have no idea which bearing...
I pulled my axle today to find out why my tire was leaning in and this is what I found.
So I am looking for an axle and found some good deals online but need a little help.
I measured from end to end and got 97" with the center of the leaf spring hole at 74 1/4". I cant seem to find one...
I have a 1995 21? Kingfisher center console with a galvanized tandem axle trailer. This past weekend I pulled the boat out to do the monthly engine run and noticed that on the front axle one of the tires is bowed in at the top. I can only assume that the axle is about to break. So never had...
I have a 1995 21' Kingfisher with a 175hp Evinrude. For the past few years I have noticed it getting harder to steer. Not knowing I put hub grease on the cables. Yesterday I noticed it very hard to turn. So I took both cables off and noticed one not moving. Looked at the helm and saw that the...
After trying to start the motor with no luck I pulled off the top carb (due to motor sitting for 3 months). Pulled the bowl off and just by the eye could not see that the float was stuck. But did fell what I can only describe to be really fine sand in the bottom of the bowl. Not much at all just...
I let the motor set up for about 3 months. Went out hooked up the water hose to it and fired her up (by the way its electric start). Let it run for about 5 minutes and killed it. Went back 2 days later to run it again and it will not start. Tried for about 5 minutes till I saw gas and oil...
I have an old Great White 55# 24V trolling motor that started making a scratching noise the other day. Kinda sounds like the barrings are gone or the prop shaft is bent. When I try to turn the prop by hand it is pretty hard to turn. Took the prop off and it was still hard to turn by hand. The...
