Recent content by runningbear888

  1. R

    need help 3 cyl 90 hp merc

    it would be greatly appreciated if someone could help me out with some info on my 1994 stinger xL 120 JET DRIVE BOAT.I need to know the settings for the three air screws top carb is 1 1/2 the middle 2 and the bottom one is 2.Also the correct timing degree.how fast should this boat go .Right now...
  2. R

    3 cyl 90hp merc jet drive

    it would be greatly appreciated if someone could help me out with some info on my 1994 stinger xL 120 JET DRIVE BOAT.I need to know the settings for the three air screws top carb is 1 1/2 the middle 2 and the bottom one is 2.Also the correct timing degree.how fast should this boat go .Right now...
  3. R

    90 hp merc problem

    Could someone tell me if the cylinders on this motor are chrome plated and if they are do you know if there are replacement sleeves avaliable or is the block now junk. 2 cyl has a gouge in it i was told the cyl could be chrome plated serial# is oe072343.thanks
  4. R

    90 hp 3 cyl merc

    Could someone tell me if the cylinders on this motor are chrome plated and if they are do you know if there are replacement sleeves avaliable or is the block now junk. 2 cyl has a gouge in it i was told the cyl could be chrome plated serial# is oe072343.thanks
  5. R

    2hp evinrude

    I just picked up this motor could someone tell me the year. serial # c7187487 model # e2rcrs.Would anyone happen to have a spare carb for it. i'm willing to buy it.If so email me at aaabiron@sympatico.ca thanks my name is ron
  6. R

    Years of motors

    I have two chrysler outboard motors I just picked up. I need to know the years of them. One is a 6hp model #6702, seriel #1238. Would you happen to know the settings for the fuel mixture screws on the carb? The other is a 9hp model #9504, seriel #1393c and the settings for the fuel mixture...
  7. R

    MARINE DOCTOR

    COULD YOU EXPLAIN THIS.My motor has two marks on the flywheel. The first one is 0 and the next one is 36. There is a small plate on the front of my motor with lines saying -4 and then +2. Could someone please tell me briefly how to set the timing?
  8. R

    Timing for 1971 , 105hp chrysler

    My motor has two marks on the flywheel. The first one is 0 and the next one is 36. There is a small plate on the front of my motor with lines saying -4 and then +2. Could someone please tell me briefly how to set the timing? Is 32 the proper degrees? and is that at wide open throttle? Thank...
  9. R

    Year of my motor

    Could someone please tell me the year of my chrysler outboard? I know it is a 105 hp. Model #1057BB Seriel #3019 and could someone tell me the setting for the points, and the timing degree?<br />Thank you very much,<br />Runningbear.
  10. R

    the marine doctor

    i'm looking for the stator for 1976 115 hp mercury<br />thanks
  11. R

    115 hp merc parts

    anybody have parts for 115 hp merc 1976
  12. R

    115 hp merc

    Could someone tell me if they have come across this problem? Mercury 115hp 1976, timing set at 21 degrees, fuel is syncronized with timing as according to manual, new fuel pumps, carbs were cleaned, Seafoam ran through it. The engine, when taking off from a stand still, takes a few seconds to...
  13. R

    oil to fuel ratio needed

    Could someone tell me the proper oil to fuel mixture for a 1976 115 hp Mercury outboard? Also, how fast should this motor push a 16.5 foot fiberglass boat? The boat runs at about 28 mph with 2 people in it, when one person goes to the back of the boat it picks up another 4-5 mph. Thanks for...
  14. R

    NEED HELP BADLY

    I have a 115hp mercury outboard motor. I lost number 3 cylinder. I tore the engine apart and cleaned the cylinder and replaced the number 3 piston. Everything else is in A-1 shape in the bottom end. Lost #3 piston due to cut vacuum line on that cylinder. I don't know the year but the serial...
  15. R

    115hp timing steps

    Could someone please tell me the steps on how to time a 115hp mercury outboard? Seriel # 7003976.<br />This engine has the distributor. Thank you very much, your knowledge is appreciated.<br /><br />Runningbear
See more
Top