Recent content by tom2

  1. T

    Suzuki DT4 water circulation problem

    HI, I have a Suzuki DT4 when I remove the flushing plug while the motor is running I get a full volume of water and pressure, however no water comes out the pee hole just exaust pressure.Does anyone have any ideas.Is my motor over heating even if water sprays out the flushing hole?Thanks for the...
  2. T

    clunk noise under flywheel

    Hi, Hi have a 84 50 hp evinrude and when I rotate the flywheel I hear a clunking noise.I removed the flywheel and made sure every thing was tight.But it still clunks.Could I have a warped flywheel? Thanks
  3. T

    force and chrysler are they the same?

    I have a 84 85 hp chrysler. Would a 86 85 hp force be the same identical powerhead?Is so for how many years were the the same? Thanks,Tom:'(
  4. T

    Can't find year of this mercury

    Someone gave me a mercury motor and the only numbers I can find on it is the ser # A195182.I don't even know the hp.The person said he thinks its a 50 hp it has 4 cyl. Thanks for the help
  5. T

    Question on reed valves

    I have a 84 50 hp Merc .Is it a hard job to change these valves? Is there any way to check or test them before dismatling the engine?Thanks for the help
  6. T

    Help with merc control cables

    Are all merc control cables the same from year to year.I hav e a set of cables from a 71 or 72 merc.Would they fit a 1985?. Thanks,Bob
  7. T

    Firing problem 50 HP Merc

    I have a 1984 4 cyl 50 hp merc. When I pull the wires off either #3 or 4 the motor will stall out. I seems to make no difference in the way the motor runs when I disconnect #1 or 2 cyl. compression is 120 in all 4 and I have good spark. Thanks for your help. I rebuilt the carbs but It looks like...
  8. T

    What horse power is this motor

    Model # 1050625
  9. T

    what horse power is this merc

    model#1050625 thanks
  10. T

    What year and Hp is this mercury

    Ser#195182. Thats all I have It's a 4 cyl in line motor. Thanks,Tom
  11. T

    Is it a blown head gasket

    1992 70hp Force compression readings are #1-125 #2-55 #3-90. Could this be a blown head gasket or possible piston and cylinder problems. Thanks for the help.Tom
  12. T

    Suzuki DT4 water flow

    I replaced the water tube and the impellar assembly in my DT4 and still have a water flow problem. water just dribbles out the pee tube and it seems like the warmer the motor gets the less pressure.I do notice exaust pressure at the flow tube.Is this normal?<br />Thanks for the help
  13. T

    Flywheel tries to turn when I hook up the battery

    This is a 1977 70 hp johnson.After sitting for a while I hoohed a battery up to the motor and I noticed a arc at the battery terminal.And noticed that every time I would attach the battery the flywheel tries to turn.I disconnected the ignition plug and also pulled the plug wires thinking the...
  14. T

    50 hp johnson does nothing but backfire now and then

    Hi,<br />I have a 1985 50 hp johnson that does nothing but backfire through the exaust every once in a while while cranking.. It was running great then the next time I went to start it this happened. Compression is 130 on both cylinders and has good spark.Could the ignition module be bad? I...
  15. T

    Need help with year of chrysler

    Any know the year of this motor model #857HC and if it will bolt up to a 1984 85 hp.Thanks for the help
See more
Top