Recent content by tractoman

  1. tractoman

    Gimbal bearing seal question.

    Thank you all. Gonna replace gimbal bearing soon and want to have all the parts I need on hand. Using a greasable bearing. Just seems to make more sense to me.
  2. tractoman

    Gimbal bearing seal question.

    I know it’s a dumb question but do all outdrives have a seal ahead of the gimbal bearing and does one change it routinely with the gimbal bearing?
  3. tractoman

    Alternative to drilling your alignment tool to install gimbal bearings

    So the 1-1/2 pipe is used as a slide hammer on the outside of the alignment tool?
  4. tractoman

    4.3 LX Gen+ Alpha leaking water/oil mixture

    I just had this same issue on my boat. We missed a season getting it out and I just noticed gear lube leaking out the water inlet ports on the lower unit. I did a fiull waterpump service and the water pump base seal carriera assembly.was where I found my leak. Part #807929A1. Assuming you have a...
  5. tractoman

    Gear oil leaking out of lower unit.

    Noticed today my alpha 1 gen 2 is leaking gear lube. It is coming out the lowest water inlet hole. Boat has not been out since last season. Trying to think of how lube would get here. I’ll probably replace the impeller and water pump housing but seems to me like it would be coming through the...
  6. tractoman

    Disc Brake Conversion Kits

    I am looking to convert from drum to disc brakes on my trailer. It is a tandem trailer with brakes on only one axle. Fully loaded my boat and trailer are about 3750lbs. Which brands or kits are preferred around here? I am only in fresh water so not concerned about salt but mostly better braking...
  7. tractoman

    Audible warning switch location

    On a 1995 4.3LX is the fuel pump safety switch located near the oil pressure sending unit serving double duty to set off the audible sounder in a low pressure situation or is there another switch somewhere? Engine serial 0F588532
  8. tractoman

    1995 4.3LX with high oil pressure

    My oil pressure gauge is showing higher than normal, (I think) oil pressure. I just changed the oil, filter and sending unit and at cold idle gauge is showing around 56lbs. I used 25W-40 marine oil and a Napa Gold marine filter. I haven't been out on the water yet but I have searched and seen...
  9. tractoman

    How hot should drums get?

    I just replaced both wheel cylinders, bearings, races, seals, hub drums and bled the brake system. On one side the drum is significantly hotter than the other. I think the shoes are a little tight on the one side but am looking for guidance. Hubs are warm but not hot to the touch and a little...
  10. tractoman

    Titan Model 60 Filler Plug Threads

    Does anyone know what the thread pitch is for the cap on a Titan model 60 actuator? I want to get the attachment for my power bleeder but I am not sure which one I need.. It looks like the same cap as the Tie Down 125 actuator but I am not sure. Or, does anyone know the proper Motive power...
  11. tractoman

    LED lighting question.

    Can I mix led and non led lights on my trailer or do I need to convert all at once?
  12. tractoman

    Speedo and pitot tube accuracy.

    Is there a way to make the speedo and pitot tube system consistent on an alpha gen II? I know it is not that important but would sure be nice if it were somewhat accurate.
  13. tractoman

    Need to replace bunks and have a few questions.

    I have a painted steel trailer. I need to replace the bunks which are 2x6x8. Should I use PT lumber or not? Should I use galvanized hardware or stainless to attach bunks? It will be carriage bolts. I will glue and staple or use galvanized roofing nails for the carpet. If I staple should I use...
  14. tractoman

    General Prop Theory Question

    On my '95 Sea Ray 180, 4.3LX Alpha Gen II 1.81 ratio, I had been running an aluminum 19p x14.5 prop. Switched to a stainless Mirage 19p x 15.75 (I think that is the diameter) prop. The Mirage just feels like it's too big. The boat gets up and goes but feels like the larger prop is putting too...
  15. tractoman

    Bunk building and replacement

    I need to replace my bunks. They are currently through bolted to the trailer flanges where the bunks sit. I'd like to do it this way again but the question is, should I use carriage bolts or standard bolts, and in either case should I fill the void left by countersinking them with epoxy or...
See more
Top