Search results

  1. C

    1993 Mercury (8 HP) outboard. Propeller shaft doesn't turn

    Just picked up an 8HP outboard off Craigslist for $200 (no prop though). The engine runs the gear shifter seems to work. However when I put in gear the lower horizontal shaft (prop connects to) doesn't spin. The previous owner said he hit a sand bar pretty hard and the issue is most likely in...
  2. C

    1951 Evinrude 14hp 4441 - Need carb kit and impeller

    I'm having a hard time finding a carb kit and impeller for a 1951 Evinrude 14HP (modal 4441). I've never had an problem finding parts for Johnson/Evinrude motors but this one is taking its toll. Any help would be greatly appreciated.
  3. C

    Crigslist Ad for 1983 mercury 7.5 hp (asking $550)

    AD: Seems like a good deal but I don't know a whole lot about the older Mercury outboards. Are the older mercury outboards known for having problems? I've always stuck with Johnson/Evinrude motors from the 50s and 60s and they have always been very reliable. Does $550 seam like a good deal...
  4. C

    Sheared off flywheel bolt (1957 Scott Atwater 3875 10HP)

    I was given a 1957 Scott Atwater (10HP) outboard; which has been sitting for so long, the pistons are seized. Two cans of WD40 and a week later, the pistons finally break free. But I ended up shearing off the flywheel bolt in the process... (nothing was used for additional leverage, All I had...
  5. C

    Briggs & Stratton 5hp - Craigs List AD

    I'm looking for 5 - 7HP engine. This deal seems almost too good to be true though. It's a newer motor and he/she is asking @ $400 for it. Does this raise any red flags? http://toledo.craigslist.org/boa/1823346904.html
  6. C

    1956 Evinrude Lightwin 3HP - 2 MPH!

    I rebuilt the carb and fired it up in a trash can; adjusted the low and high speed valves; water is flying everywhere! The engine sounds really strong. Great! :D I mount it to my 12ft john boat and take for a spin. At full throttle, the engine RPMs is NOWHERE near what I getting during my test...
  7. C

    1956 Evinrude Lightwin 3HP - Overheating

    I have heard that the older Evinrude motors were designed to run slightly hot. But, what is too hot? I replaced the impeller and started up the motor in a trash can. After allowing the engine to run at full throttle for 5 minutes, I used an IR gun to get some temperature readings. Directly...
  8. C

    Mid 50's Evinrude Fleettwin (Seller Wants $50)

    I posted a wanted AD on craig's list for an old Evinrude motor that needed some work. I got the following email today (no pictures were sent): I called the seller and was told the motor sat in his grandfather's shed for many years and the pistons are seized up. The seller also stated that...
  9. C

    1956 Evinrude 3hp Lightwin - Did I buy the wrong Carb Kit??

    According the merchant's website, this kit should work for my carburetor. http://www.boatsportandtackle.com/servlet/the-1051/CARBURETOR-KIT-WITH-FLOAT/Detail Yet, I cannot find any other references online stating this is the correct kit. Everyone else (forums, blogs, various e commerce sites)...
  10. C

    1956 Evinrude - New Impeller (tight fit?)

    I used www.outboard-boat-motor-repair.com as reference for ordering new parts. This is a great site; I cannot thank the author enough for sharing this information. While I was tearing apart the gear housing, I noticed some differences with the replacement part (NAPA Part Number 18-3001). For...
  11. C

    Low head dams

    Went tubing down the Raisin River today (Monroe, MI) and was caught in the backwash of a low head dam. Didn't realize the damn was ahead until it was too late. Fortunately the tube didn't flip while I was going over it; I did have my PFD on. I'm not sure how long I was stuck; my best guess is 5...
  12. C

    12 ft Jon boat ? Transom Replacement

    I have a very old (badly beat up and patched) Jon boat I purchased for $100. My goal is to restore this boat for some weekend Bass fishing. The transom wood was so rotted; I was able to remove 100 % of the wood with my bare hands. I removed both aluminum corner supports and attempted to bend...
  13. C

    Help Wanted (i.e. idiot?s guide to buying a used outboard -10 HP or less)

    I?m seeking advice for purchasing a used outboard motor (10 hp or less). All suggestions are welcome and greatly appreciated. Scenario: 1, Initial phone/email conversation: You find a good deal on Craig?s list (or news paper ad, boat trader, etc) and decide to call/email the seller. 1a...
  14. C

    Evinrude 3hp Lightwin Pouring Gas From Carb

    Just rebuilt the carburetor on an old litewin; the engine screams when I fire it up! I?m shocked how this 50 year old engine runs. I?m just having one minor problem?I can?t figure out my carburetor is leaking. I?ve torn the carb apart 4 times and adjusted the float with NO success? The engine...
  15. C

    1956 Evinrude 3hp Lightwin Carb Float

    I cannot find a carb rebuild kit (with a float) that?s compatible with a 1956 Evinrude 3hp Lightwin. The float needs to be replaced. I also found some posts which mention a ?clip? (small spring) that is attached to the needle? My needle does not have this spring, is this spring necessary for...
Top