Search results

  1. ONERCBOATER

    Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc?

    Re: Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc
  2. ONERCBOATER

    Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc?

    Re: Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc
  3. ONERCBOATER

    Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc?

    Re: Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc
  4. ONERCBOATER

    Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc?

    Re: Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc
  5. ONERCBOATER

    Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc?

    Re: Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc
  6. ONERCBOATER

    Any Interest in detailed Carb removal/rebuild/replacement pics for 1986 45hp merc?

    I just took a huge amount for a customer who wanted to see the "dirt" in the carbs.... needless to say I always take pics of wiring on way in and figured what the heck and pretty much took step by steps of the entire process. If there is interest I will post em... if not i'll save the bandwidth...
  7. ONERCBOATER

    looking for link and sych directions for 1994 mariner/tracker pro 40hp

    trying to help a friend get his boat up and running.....carb kits done, fuel pump replaced... carbs not synched yet... and want to make sure timing is correct before further operation..... my bro in law made bit of a mess trying to help these peeps out.... engine idles like a dream... but cuts...
  8. ONERCBOATER

    mariner 40hp manual.....94 i think.. looking for factory manual

    as it says looking for factory manual service/repair believe engine is a 1994 40hp tracker pro by mariner serial number OD289893. Cant find on ebay or amazon... any other ideas..... thank you in advance
  9. ONERCBOATER

    Last try for help with 50 hp shift lever.

    Re: Last try for help with 50 hp shift lever. pics uploaded for him
  10. ONERCBOATER

    just thought i would share result...of 20ft pontoon with 20hp engine 7p 3 blade prop

    20 ft tracker pontoon, 20hp 1978 merc 7p 3 blade= 5500-5600 rpm and about 12 mph. now i doubt that most would consider this sufficient power, but it easily pushed me against a 19mph wind, and though slow, was remarkably efficient at 3500-4000 rpm. You also have to consider that there is a 10ft...
  11. ONERCBOATER

    question about moving axles and tongue weight

    I am looking at moving the axle (total length 24ft axle center at 18 foot from hitch, wanting to move it to 16ft from hitch to take some load off my hitch... currently there is more than 600lbs (judged by 3 strong men not being able to lift tongue) on my hitch and I don't like that. looking for...
  12. ONERCBOATER

    Correct Rebuilt 1972 1972 9.5HP 18-7823 fuel pump

    Re: Correct Rebuilt 1972 1972 9.5HP 18-7823 fuel pump ok.....these can be a real bugger if your not familiar with them.... 1st time i played with one was out on lake, of course in an out of the way cove away from anyone and at the wrong end of the lake.... took me a few hrs of hanging over...
  13. ONERCBOATER

    just thought i would share my new project

    Re: just thought i would share my new project [
  14. ONERCBOATER

    just thought i would share my new project

    Re: just thought i would share my new project ok got pics to share.... please remember this is a project in a state of flux and by no means done.
  15. ONERCBOATER

    aluminum solder....the harbor freight stuff works!!!!

    well in a differnt area of the forums I have been documenting the creation of a differential steered trolling motor system for my 20ft pontoon, while making the motor mounts for this system which are made of 4" T6 aluminum C channel and 2"x1/4" T6 aluminum bar stock I made an error in the...
  16. ONERCBOATER

    hello again, thought i would share a different method of operating trolling motors

    Re: hello again, thought i would share a different method of operating trolling motor these are 3d rendering of the mounts I am building to accomplish automated raising and lowering of the trolling motors, I am 3/4 of the way done with one mount at this point and working up a locking...
  17. ONERCBOATER

    walls for a pontoon boat cabin (like micro houseboat)

    what I origanally wanted was http://cmi-insulation.com/products/PDF/Thermax%20Heavy%20Duty%20Plus%20%2825%29.pdf but i can't get access to it here in Yuma AZ. so I am thinking that I can make a reasonable copy with covering both sides of dow corning pink 0.5" foam with epoxy/glass or...
  18. ONERCBOATER

    how to lift pontoon from trailer, to work on trailer and pontoons??

    OK, i have a problem, I am stripping old epoxy paint from the pontoons :( , and I need to be able to get under the pontoons to strip it there as well. I have the pontoon bunk style trailer rather than a center lift. I also have a few small holes in the pontoons at this point that I need to braze...
  19. ONERCBOATER

    hello again, thought i would share a different method of operating trolling motors

    I put this in the pontoon section because, it is going on a pontoon, and it it most applicable to houseboats and pontoons. The modifications to my 20ft pontoon continue as does the work. A few weeks ago I was fortunate enough to get a pair of Minn Kota trolling motors,4 swivel seats, and two...
  20. ONERCBOATER

    pics of where you put your furniture and why

    Re: pics of where you put your furniture and why mine is coming along nicely, I should be able to provide pics of the whole deal... however best i can do at this moment is a few snapshots off of the google sketchup i did of her that we are working off of to make into reality. there are a few...
Top