Search results

  1. 2

    galvanized bunk bracket 4" X 5" size, for C channel 1 1/2" X 4"

    hey need help finding replacement galvanized bunk brackets that i cant seem to find. They are L bracket. that mount on C channel frame(1.5" X 4"). Everywhere ive looked all they have is for 3"X3" tube brackets. Thanks in advance
  2. 2

    Timing after disconnecting oil injection

    hello all, i have a 98 mariner 200efi, i've disconnected the oil injection about 10 months ago. I've noticed everytime i try to crank it up after sitting few days now that i have to have throttle half way to get it to start, then when it starts i have to back throttle up pretty quick. its...
  3. 2

    over heating warning horn question

    hello all, i have a 98 mariner 200 efi. went to check temperture senders other day by grounding them and listening for the warning horn to go off. did the starboard side with no issues worked fine. went to do the port side and has the 2 brown wires with black stripe. i grounded each one and no...
  4. 2

    will omc tachometer work on mercury 2.5L

    hello all. was wondering if a omc brand tachometer work on my 98 mariner 200efi? my boat came with a evinrude on it and had all omc gauges. after i put mariner on boat i put new teleflex tachometer on there didnt even try the omc just thought it wouldnt work. all my gauges look same except the...
  5. 2

    setting timing @ cranking speed

    hello all.. i got a 1998 200 efi mariner and when i set my WOT timing i left #1 plug in only and set timing. my buddy says im suppose to take all plugs out to set WOT timing. didnt think it would be much difference but checked it after i set it with #1 plug in and took plug out and checked...
  6. 2

    Detonation controller assembly and timing

    i have a 1998 200 efi mariner offshore.i see the wire that comes out of detonation module thats suppose to go to detonation sensor and it is cut and now goes to a ground. does that mean now that detonation controller assembly is not advancing my timing now. i read if detonation controller...
  7. 2

    Removing Detonation controller assembly box

    hello all. i have a 98 mariner 200efi. i just recently removed my oil injection system along with the warning module. while i was there was looking at the detonation controller assembly right above warning module. Was wondering if i really needed this anymore since it doesnt even have the knock...
  8. 2

    disconnecting oil injection on 98 mariner 200efi

    hello all. craziest thing happened other day.2 weeks ago went out on boat for the day and all went well.when i got home no issues just parked in slip like i usually do and left.last weekend went down to take boat out of water.had truck and trailer in water at launch.started boat and instantly...
  9. 2

    200efi bogging mystery

    hello all. i have a 98 mariner 200 efi. been having bogging issues when i thought was just when it was cold. what i was normally doing was while loading my gear and stuff on boat i would have it running.so normally it would be running about 10 minutes and when left dock and short distance away...
  10. 2

    98 200 efi boggs when only cold

    hello all, ive posted on here before about my motor bogging all the time just at take off. on motor before it didnt matter if it was cold on not, could of just run in from islands which is about 20 minute run and if stopped for a minute in idle then go to take off sometimes would just bogg for a...
  11. 2

    idle timing on 98 200efi

    hello all.got question for y'all.on sticker on my motor says idle timing is 4 degrees ATDC.i read that is engine warm and in foward gear.originally timing was set at 0 degrees when i checked it at cranking speed with ECM disconnected.i rechecked it later in water to make sure.my problem is it...
  12. 2

    max W.O.T. @ 5200

    hello all. my max rpm is 5000 to 5800 according to manual. my motor is getting to 5200rpm. was wondering even tho not hitting closer to 5800 am i over propping motor. my only issue with dropping pitch is that i heard if i go down pitch boat will go slower. and dont want to lose any speed but...
  13. 2

    mounting primer bulb

    hello all. seemed to have primer bulb issues. i had it mounted vertical for awhile and this year motor seemed to be running out of fuel and when pumped bulb it seem always low in pressure.other day after getting to fishing spot and motor acting up on way out i moved primer bulb in differnt spot...
  14. 2

    stumbling issues on 98 mariner 200efi

    hello all. for last 3 years had issue just when i was taking off it would seem to be stuck at around 2500 rpm and just be bogging wouldnt go over. then after tryin few things it would finally take off. after taking off always ran fine no issues just at take off. it ran the same when i was out...
  15. 2

    fuel pressure on 200efi

    faztbullet got quick question. was wondering if i have 36psi when running good and when acting up if it could still be a fuel issue. i opened vst and cleaned final filter but was already pretty clean. i believe i checked all electronics and no smoking gun yet. thanks in advance ted
  16. 2

    disconnecting idle stabilizer on mariner 200efi

    hello i have a 98 mariner 200efi and want to disconnect the idle stabilizer on it.its runs fine at idle.can i just disconnect it and not retime it.i read stuff about disconnecting it and to check timming.but was wondering if its idling fine now that timming should be good.thought if its idling...
  17. 2

    98 mariner 200 efi bogging down

    hello all. need help figuring out issues with my mariner. first of all it does'nt do it all the time.can go few trips with no problem.then on other trips can do it couple times or ten times.its when i go to start taking off and i got throttle at full throttle it won't go over about...
Top