Search results

  1. alldodge

    NOCO LifeP04 in lawn mower

    Mine is a 20hp Honda, forget model but it's about 25 years old
  2. alldodge

    Boat won't turn right at speed

    Good news, thanks for the update
  3. alldodge

    Outdrive tight after steering pin and lower bushings replaced

    Your probably fine. I would not worry about the PS because it's designed for a whole lot more load then a stiff pivot point
  4. alldodge

    Painting the bottom of a yacht

    Welcome Many use Marine Tex epoxy to fill voids in Gelcoat and cracks it glass prior to barrier coats.
  5. alldodge

    2005 3.0l Mercruiser

    Welcome Agree you need to remove the motor to replace the rear mounts My question is what makes you think they do need replaced?
  6. alldodge

    NOCO LifeP04 in lawn mower

    My thought is it fires from heat and weak spark. Spark was weak and didn't burn the fuel fully and intake started to open The NOCO Bat said it had an internal regulator which managed the charge. Every thing was fine for all year until it went dead the first time
  7. alldodge

    NOCO LifeP04 in lawn mower

    Same as 2 cycle outboards, right?
  8. alldodge

    NOCO LifeP04 in lawn mower

    I remember discussing this before but unable to find my thread. If someone finds it we came merge it to keep together Had problems with lawn mower Bat staying charged so I installed a Bat cut off switch and then a NOCO LifeP04 Bat. All worked good until one day I forgot to turn Bat switch off...
  9. alldodge

    Odyssey Battery

    Went to cur my grass one last time and Bat went dead. Took the old Odyssey Bat removed from seaqdoo and installed in mower. Fired it up with a few grunts and got lawn done Both Seadoo and mower get PC925 Bats next year
  10. alldodge

    Distribution housing leak?

    Double check if the old o-ring gut stuck on the face and there isn't 2 there now. If no to double rings then guess it's cracked
  11. alldodge

    Boat won't turn right at speed

    Bring a measuring tape and get the distance from the top of the ventilation plate to top of water. Also is the drive straight up and down?
  12. alldodge

    Outdrive tight after steering pin and lower bushings replaced

    Depends on how stiff, stiff is but most likely it will loosen up. Was the newer nylon bearing (item 4A) used?
  13. alldodge

    Boat won't turn right at speed

    Welcome Can you post a pic of the stern wit motor full down?
  14. alldodge

    Do they make boat nav light wiring harness kits?

    Basics wiring Other then the motor wiring
  15. alldodge

    3.0 engine removal

    Move throttle full forward before removing drive
  16. alldodge

    Temperature Gauge not working - Volvo Penta 5.7 GI-E

    Pull the connector apart
  17. alldodge

    Temperature Gauge not working - Volvo Penta 5.7 GI-E

    Your mixing Temp sender and temp switch The gauge at the helm uses the sender in your pic and goes direct to the gauge, it does not go to the ECM Your motor also has a 2 pin temp switch that goes to your ECM (assuming J2-7). The temp switch closes when the temp gets to hot and sounds the alarm...
  18. alldodge

    Temperature Gauge not working - Volvo Penta 5.7 GI-E

    Agree, might also be the 10 pin connector. Have seen many times that the pins get corroded and some break away internally Can check with ohm meter
  19. alldodge

    Temperature Gauge not working - Volvo Penta 5.7 GI-E

    Welcome The gauge has at least 3 connections. 12V when key is turned ON Ground Sender wire going from the gauge thru pin 3 to sender Remove the sender wire from sender. Turn key ON and ground wire, the gauge should peg Hot
  20. alldodge

    Rain needed

    This spring was highest in a while Lowest was last winter About a 23ft swing
Top