Search results

  1. L

    1993 201 ski 20'

    Does anyone know where i can find out how much my boat is worth. I looked at nada and it would only give me what the hull is worth it would not give me what the boat and motor is worth... CAN ANY ONE HELP............... It is a 1993 Ski 201... Not a fish and ski..It has a 200 evinrude 4blade s...
  2. L

    Need more speed

    I have a Volvo Penta B230 (2.3L) with a SPC outdrive in a Glastron. My problem is that at 4500 rpm I can only get around 20-22 mph. It looks as it has a factory 3 blade prop (I don't know specifics of it). My question is HOW do I get more speed out of this engine prop combination or do I need...
  3. L

    Replacing Volvo-Penta engine

    I have a 230 Volvo Penta in a 94 Glasstron and I'm about to replace the engine. My question is, besides the throttle cable and electronics and the 4 or 6 bolts (motor mounts), what else am I looking at to remove the engine???
  4. L

    1965 9.5 evinrude water impeller

    Any one know how to get to the water impeller in a 1965 9.5 evinrude 9522 C E05030. I tried pulling the 6 bolts out that hold the lower unit on but the shift linkage is holding it i can see the water impeller housing and see the shift linkage i also see the part that connects the linkage...
  5. L

    1994 Volvo Penta 230 tilt problem

    I have a 1994 Volvo Penta 230 with the volvo outdrive it is in a 1994 glastron. My trim will go all the way down and back up just a little like i guess it is suppose to. When i press the tilt button the only thing happens is the relay click"s i changed the relay and still just clicking. their is...
  6. L

    bleeding trim pump on 1987 yamaha pro v 150

    Can anyone help me? I just installed a new trim motor and now cant get the motor to stay up it will try to go up but as soon as you take your finger off the trim button it goes right back down. i dont know how to bleed it. the trim motor was off for a while and the motor was let up and down by...
  7. L

    1987 PRO V 150 H Carb Setting

    I have a 1987 yamaha Pro v 150 i just took the carbs off and cleaned them they seem fine but i need to know how to set the floats, and how many turns out is the normal setting or a good starting point on the air screws. With the floats set and the air screws at a good starting point(HOW DO I...
  8. L

    How to tighten I bolts

    I have a 1987 Skeeter 150 both of my i bolts are coming loose i can not find the nuts any where. I have looked inside the boat from both sides a there is not anything.
  9. L

    Oil Injection Working?????????????

    I have a 1987 yamaha pro v 150. how can i tell if my oil injection is working. I just bought the boat and i am still working on the clean up and cleaning the motor parts i have only ran it on the hose.
  10. L

    Real High Idle

    Ideling at about 2000 RPM then it will cut down like it wants to cut off and then right back up to high idle. Just bought the boat so dont know alot about about it. It is a Yamaha PRO V 150 1988. Cranks right up.It also is popping and running a little rough.I sprayed carb cleaner in the carbs...
  11. L

    yamaha pro v 150

    wanting to take my oil injection off so i can mix my on oil b/c i heard these motors are bad about messing up b/c of the oil injection not working. what all do i need to do. :redface:
Top