Search results

  1. jimmbo

    Have you ever seen this?

    It took only a few seconds to Download the Video.(I have a slow, 30mb copper DSL service. Phone company has been threatening disconnection if I don't switch over to Fiber). Watching the Shift Lever boogieing like it is listening to 'shaking all over', you might consider pulling the Gearcase...
  2. jimmbo

    1979 40hp lower unit stuck

    If you have a Dremel you could try cutting several Slots in the Crank Shaft, then use a Chisel on them, along with a bit more Heat. Just don't cut into the Drive Shaft. You could also try Chilling the Drive Shaft with some CO2, whilst Heating the Crank Shaft. Removing the lower Crank Shaft...
  3. jimmbo

    Just thought I'd share a nice photo.

    It was over 82F, yesterday in North Central Alberta. Only thing that made it bearable was very little Rain so far.
  4. jimmbo

    1976 135HP Evinrude No gas going to spark plugs/cylinder

    There is a Picture Thread, in the Dockside Chat Section I saw some Northern Lights about an hour ago, but I was in the City, so...
  5. jimmbo

    1978 mercury outboard

    A 78 will have a Cowl Decal like this
  6. jimmbo

    Is this trailer repairable?

    No, simply the Friction of the Bunks/Rollers against the Hull
  7. jimmbo

    Is this trailer repairable?

    EZLoader does have replacement Parts, mainly for Warranty, but in your Case, just replace the Trailer. Less Headache, and might even be less expensive
  8. jimmbo

    1976 135HP Evinrude No gas going to spark plugs/cylinder

    There should be a Drain Screw(Hex Head with Slot) on each Carb Bowl #35. That can verify that Fuel is getting to the Carb, but doesn't mean the Fuel is getting through the Carb
  9. jimmbo

    No sparking v4

    Any Over-torqueing of a Tapered Fit, will ruin the Flywheel, requiring it be replaced Using an Impact for Tightening is the sign of a Bad Mechanic
  10. jimmbo

    No sparking v4

    I would say that using an Impact Gun in place of a Torque Wrench is not Common Sense, especially on a Tapered Fit. Overtightening will Ruin the Flywheel
  11. jimmbo

    back pressure out of carb 91' 155 hp Mercury.

    If the Carb is spitting Air-Fuel out of it, then the Reeds need to be inspected. A 91, the reeds will be relatively easy to Access, as they are external to the Crankcase. Carbs have be removed first, then the Intake Covers, and then the Reed Assembly. Upon reassembly, a Link and Sync will need...
  12. jimmbo

    No sparking v4

    As mentioned, there are Tools for that, I've used a Strap Wrench, others have found places to Wedge Pieces of Wood to jam the Flywheel.
  13. jimmbo

    Gas - Oil Mixture on old Evinrudes outboards

    Mixing is indeed needed to mix them to gether
  14. jimmbo

    Gas - Oil Mixture on old Evinrudes outboards

    When poured in, it will settle on the Bottom
  15. jimmbo

    Mercury 85HP Thunderbolt Ignition Series??? Whats missing??

    The 72 80hp and the 73 85hp are very different engines. They might have the same Bore and Stroke, but the Induction System is much different. Carb Calibrations would be likely different between the 4 and the 6s The 1978 and later 80hp engines are not the same as the 72 and earlier 80hp This...
  16. jimmbo

    Am I under proped?

    Early in the Season, when the Air is Cooler and Drier, an engine will make more Power than during the Hotter and more Humid Days of Summer. so in July the Rpms may very well be at 4800
  17. jimmbo

    1976 135HP Evinrude No gas going to spark plugs/cylinder

    If it has spark,(a spark at a Plug, in open Air, really means Nothing). Can the Spark jump a 3/8" Gap? Is there fuel in the Carb Bowls? if not, there could be a blockage, or gummed up Inlet Valves in the Carbs I hope you are not trying to start/run it without a supply of Water for the Water...
  18. jimmbo

    Am I under proped?

    Props may state the same Diameter and Pitch, but often are like Apples and Oranges. 200rpm over the WOT range, isn't instant Death for the Engine, but it might affect overall Longevity, though less than Over-propping would
  19. jimmbo

    How to choose an old 2-stroke 150/175 Merc

    Butchery, that is all it is. I doubt it even adds 1/10 mph
  20. jimmbo

    How to choose an old 2-stroke 150/175 Merc

    So the Exhaust now also comes out the Water Discharge Drains just above the AV Plate, which will also dump more water into the lower Exhaust Passage. Backyard Butchery
Top