Search results

  1. C

    Mercury 135 not running

    One more thing that occurred to me. The motor will not crank at the ign key when at WOT. You will still need to jumper the starter solenoid. Your kid is unemployed, I am afraid.
  2. C

    I want to place a metal patch on a Zinc-Coated steel gasoline tank opening.

    Are you planning a gravity feed of the gasoline to the generator, or some kind of fuel pump?
  3. C

    Mercury 135 not running

    21*BTDC at cranking speed is the max spark advance spec for my '93 135V6. Sure, your son can help, if inclined. Mine is usually not inclined.
  4. C

    Mercury 135 not running

    Remove spark plugs 2-6. Put timing light on topmost cylinder. It should be obvious which one it is. Gearcase can be on or off. If on, remove prop to keep it from chopping your feet. Idle pickup timing is 0-9* ATDC, and is set when the carbs are ready to open, but still closed. WOT timing is...
  5. C

    I want to place a metal patch on a Zinc-Coated steel gasoline tank opening.

    Yes, gas tanks were sealed until maybe the late seventies. The vapor pressure of gasoline is only so much. Tanks in those days were built to survive it.
  6. C

    Evinrude Mount Assy needed 5007470

    Crowley says they have 5 in stock and will ship immediately. You might try marineengine.com as well.
  7. C

    Evinrude Mount Assy needed 5007470

    Crowleymarine will ship in 6-8 days. https://www.crowleymarine.com/evinrude/products/5007470-rubber-mount-assembly?q=5007470
  8. C

    I want to place a metal patch on a Zinc-Coated steel gasoline tank opening.

    Around here propane is harder to get than gasoline. Analysis shows that 20# of propane and 5 gal gasoline power the generator for about the same time and cost. A much cheaper alternative is using natural gas as a fuel. Most gasoline generators can be easily converted to natural gas or...
  9. C

    How long is the skeg on a mariner 30/40

    You could put 2 straight edges on the undamaged parts of the skeg, and see for yourself the length and shape.
  10. C

    Mercury 135 not running

    It is very easy to check the timing. The check will give peace of mind, no?
  11. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    It is more useful to add a bit of garlic and onion powder and some oil to the vinegar and salt mix and pour it on your salad.
  12. C

    1972 80 Hp Mercury enhine

    I wrapped my hydraulic lines with electrical tape. It looked OK and lasted many years.
  13. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    You realize that vinegar and salt mixed together is not HCL, right? There are 10K perpetual motion machines on the internet as well. Those are crap as well.
  14. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    Gee, I am not sure how to fill and seal the cooling system of an outboard. I doubt vinegar will do anything. What is the purpose of the salt?
  15. C

    I want to place a metal patch on a Zinc-Coated steel gasoline tank opening.

    Top of tank right? Standard fuel tank gauge senders are sealed with rubber gaskets and self tapping screws. Tanks are vented, so no pressure build up is expected.
  16. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    I pumped this stuff thru my motor for 4 hours. I am not sure it made a difference. Any other opinions?
  17. C

    ETEC Emm Issue

    I saw a video of a guy working on a FICHT, which is the father of your motor. It has 4 fuses in a plug, attached to a cable. The fuses were under a cover, that looked like a cable terminator. You might look for such a thing, if you did not find 4 fuses together.
  18. C

    ETEC Emm Issue

    Does that e-Tec have any fuses?
  19. C

    1963 Starcraft Jupiter 16ft Windshield Brackets

    My '62 Crestliner had small U shaped brackets to hold the very bottom back edge of the windshield to the deck. Is that what you are looking for?
  20. C

    Shift rod position after impeller change

    The mechanic may be correct. The shift cable could have been set (by the mechanic) just a bit wrong. Set the control to neutral. Disconnect the shift cable at the motor. Now move the shift lever until centered in the neutral position. Adjust the shift cable to match the shift lever and...
Top