Search results

  1. B

    89 /200 evinrude no spark

    lots of gas but no spark what to check first
  2. B

    carbon build up on piston

    can carbon build up lower compression 1 cylinder135 other 120 seadoo piston has thick black layer on piston or should i look other places
  3. B

    97 gs seadoo is it crank problems

    hard to start have to feather throttle after cranking alot. compression test done 135 and 125 lbs 10 pounds difference in cylinders,what should i check???? rotary valve, rings, carberator tcw3 oil was added by mistake ran 1 day on it an then empty tank and put fresh seadoo oil
  4. B

    2005 pontoon MPH gauge

    Have fisher 2005 pontoon w/ 3.0 inboard engine mercruiser the MPH gauge quit workin the air tube tryed blowing it still no luck any help to check on gauge or motor, lower unit
  5. B

    97 gs seadoo rattle

    Engine runs good but a small rattle comes from front lower engine at stator box, feel lower block and jug is warm in this area, is this normal ?feel lower jug and block on other end and nice and cool.could it be bearing getting hot.
  6. B

    97 seadoo compression confused

    97 gs new pistons and rings first put in got 149 lbs compression now week later 1 cylinder same an other 130 lbs what could of went wrong
  7. B

    stator, cause metal to stick to crank hhhelp

    seadoo missing one needle bearing off piston seems like crank is magnetic and maybe holding needle bearing on crank or something, any suggestions if i unhook stator will this demagnetic the crank?? OR ANY SUGGESTIONS HAVE VACUUM AND BLOW HOSE BUT NOTHING COMMING LOOSE have to find before rebuild.
  8. B

    seadoo salt water(help}

    guy has seadoos for sale 1 has 64 hrs an other has 36 hrs they were in fla. now running in fresh water , everyone says to stay away from salt water doos is that correct an why???
  9. B

    97 gs seadoo rotary valve

    have svrew sucked in rotary valve has ding in one half is it ok to file down smooth??/ and how do i keepin time if i take off
  10. B

    96 seadoo gs rebuild top end

    Dropped carb screw in motor week ago tore apart found screw,broke one piston, machine shop said jugs look good, replace w/ pro x kit. What do i need for lubs and sealants?? I know lock tite, do need to put something on gaskets of heads besides gaskets?? and same for exhaust anything besides...
  11. B

    97 GS SEADOO SUCKED SCREW(help)

    :confused::Have one screw missing on carb box mount , and skijet wont turn over, is there anything to stop the screw except crank, piston and ect.????? how much damage you think is done, do need new engine.?????
  12. B

    97 seadoo gauges

    :confused:seadoo gs gas gauge does not work,took out baffle and it is in good shape even but new float in just for good measure,tested OHMS on two pink wire out of baffle test just as manuels says thats ok,whatcould be my next test?? continuty on wires from gauge to black box plug in seems ok'...
  13. B

    96 40hp need ignition switch

    choke switch is bad which it separate from ignition ,the ignition switch is sprung and keeps starter in gauged. all i can find is magnito type need battery type w/choke built in. anyone got one or know where to get one
  14. B

    96/40hp need ignition switch

    have 96 mercury the choke switch is bad and the ignition switch is sprung. all i can find is magnito type need battery type, prefer choke and key together.any body have one or know where can get
  15. B

    2003/3.0 needs winterized

    mercrusier need to winterize soon please tell what need to do
  16. B

    40 merc what does rectifier do

    did OHMS test it showed bad,not very smart on this item choke will not operate could this be problem sense rectifier wire goes to throttle
Top